ABC2037DES Amana Refrigerator - Instructions

I watched the video provided on-line in your website, which was excellent. The information provided gave me everything I needed to change the board. I already had experience handling control boards and was aware of the static precautions; however, your paperwork was very good detailing how to program the new board. The only small problem I had was reinstalling the temp sensor in its bracket. The lead was very short. Other than that, all went well! The project took between 20 and 30 minutes.

There were three parts in question, the defrost timer (inside the casing near the control dial at the top of the refridgerator), the defrost thermostat (behind the back wall of the freezer), and the heater coil (ditto). We tested the defrost timer by opening it up, advancing it to the defrost cycle, and waiting for the compressor to start up again, showing that the timer was working. Then we replaced the defrost thermostat and found that the heater coil worked.

The hardest part was figuring out how to open the casing and get to the timer. If I do it over again I will replace the $20 thermostat first and then deal with the timer if necessary. To get to the thermostat you can easily take the freezer door off by removing two screws in the door tracks. There was even an arrow pointing to one of the screws! Take out the food trays and then unscrew the back wall with a nut driver. The thermostat was clipped to one of the copper freezer tubes. I unplugged one end of the thermostat circuit at the lead to the heater coil and then cut the thermostat out of the circuit and used wire nuts to connect the new thermostat.

Once I figured out where the part was located it was quite simple. I thawed out the freezer first. Using a nut driver, I removed all the screws to the back panel of freezer. Squeezed the clips on the ice maker attachment to release the panel. Once I opened the panel the thermostat was visible and accessible. The failed thermostat was obvious by its bulging appearance. By following the instructions found on Partselect.com, I cut the two connecting wires and removed the failed part. I then striped some insulator from the wires to connect the new part. I used electrical tape to ensure connection and insulation as the white wire connectors did not work well (too big) for my application. Closed everything back up, plugged in refer and all was good. A little time and a $20 part saved me $150. Thanks Part Select!

Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

removed the old valve from back of fridge by removing screws that held mounting plate. removed water lines by pushing in on quick connects and pulling hoses out. A little different type of connections. installed new valve and pushed hoses into connections making sure that they snaped in. reinstalled screws and checked for leaks. took about 15 minutes!

Went on line to find replacement valve.
Received the new part and compared to broken part. Both the same.
CAREFULLY removed the broken valve. Paying attention to how it came off.
CAREFULLY put it on the same way it came off.
This is a plug and play part. Just had to reconnect the water line.
Saved at least 75 dollars.
Easy to find the part on your site.

I watched video for repair and it went just like it showed. piece of cake

Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.

I searched in line for a replacement fill valve and easily found it on your site w/ excellent diagrams. I turned off the frig., & the part came out simply and logically first removing the 5 screws that hold it in w/ a nut driver. Then remove the supply water line and the other quick connect lines that feed the ice maker and the chilled water dispenser. Then, disconnect the two wire harnesses that clip off easily by hand. They feed the two relays in the valve and are color coded. Remove the valve and reverse the procedure to hook it back up. Note: a little water will come out of the lines so be ready w/ a small bowl and a dish towel. After installing the new part, it was necessary to "bleed" the water lines of air by drawing a few glasses of water from the water dispenser to get the system operating normally again. One tool, common sense, 30 minutes. Probably saved $150 + on a repair man plus parts markup. Thanks very much!!

Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.

But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.

pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Removed broken lid and snapped new one in place.