ABC2037DEB14 Amana Refrigerator - Instructions

Loosen 4 screws remove door wipe off frost pull old gasket out of slot push in new gasket instal door that was it. No help need.

take the old one out replace with new once - no instructions required, no tools needed

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed.

We came home from a long vacation to discover a warm refrigerator with its contents in various stages of decay.

Turning the freezer thermostat to its warmest setting then back to cold generated clicks, and after a few tries the compressor started and cooled the refrigerator to its normal cold temperatures. But… later the compressor again failed to start, and everything warmed back up again. With persistence and turning the thermostat up and down several times a day, we could keep the fridge cold.

It was time to order parts. We needed a new start relay and capacitor for the compressor. For our Amana ARB2214CW a start relay (WP12555902) and capacitor (WP65889-4) were listed on the first page of the Partselect parts list for my refrigerator. I ordered them, received them, removed the old capacitor and start relay (which rattled when shaken). and prepared to install my new parts. The new start relay did not match the old. The old start relay fit my wiring which had a single plug with two small female spade connectors in the plug. The new start relay required wiring with two separate female spade connectors; one the normal size and one larger. Phone calls to Partselect and to Westinghouse shed no light on the discrepancy. On the second page of the Partselect parts list was a combination of a start relay and a capacitor (W10613606) that matched my electrical connector. I could see the connection in the photograph. I ordered it and it fit. Easy peazy. That fixed the compressor start problem. Every time the freezer thermostat clicked on, the compressor started. Success.

But… from our troubleshooting we now had a thermometer the freezer, and it was obvious that the temperature difference between the cold point where the thermostat turned the compressor off and the warm point where the thermostat restarted the compressor was much too wide. In addition, the knob was hard to turn and was sticky as it turned. Oiling it fixed the sticky knob problem but not the wide temperature difference problem. I ordered a new freezer thermostat (WP67003000), received it, installed it, and all is now fine with my refrigerator. The new thermostat was physically a little different from the original, but it fit and worked.

I returned the first compressor start relay and capacitor and received a refund including the shipping charge.

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

First, make sure you have the correct part. I had trouble with mine, at first, until I realized that I had received the wrong part... it was same shape but larger. To begin, remove both fruit/vegetable drawers. Remove deli drawer. Remove deli drawer glass panel with both supports. Remove 3, 1/4" hex screws that attach end-cap. Disengage temp control slide and arm from end-cap by carefully moving parts in the direction where they will disengage. Remove temp control slide from end-cap. Now that end-cap is out, remove 2 screws that hold metal drawer slide to end-cap. Attach drawer slide to new end-cap. Attach temp contol slide and connect the plastic arm. Attach end-cap to refrigerator. Replace glass shelf, supports and drawers. Done.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

unsrewed the back plate, removed three tubes. Then I removed old valve and replaced with new. Pluged two harnesses back in the new valve. Truned water on and checked for leaks and operated the filtered water tap and the ice maker. All went well.
I really like your site for the pictures included with the part, I like to see what I'm ordering.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

The old gasket peeled out easily. No tools needed. The replacement gasket fit right in the groove. I did not need to immerse the gasket in warm water or use a hair dryer. Nifty trick: once the new gasket is in place, close the freezer door. Run your finger in the center groove of the gasket, which will push the magnet against the fridge. Leave the door closed for an hour. The gasket has then assumed a perfect fit and will continue to fit perfectly.

Pop off vent cover remove 2 screws removed cover housing and foam. Removed damper by unclipping tabs on left and right side of control lift up and out. Unplugged power wires reinstalled in reverse order.

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.