All Installation Instructions for Amana Refrigerator ABB2522FEW2

broken right deli drawer guide

Removed old guide and installed new guide

Parts Used:

Refrigerator Deli Drawer Glide

Herbert from MAHOPAC, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Too much weight on shelf over time caused it to crack down middle

Removing the old pieces & figuring out how to separate the front trim so it could be reinstalled on the new frame took the longest! (released the securing tabs with a screw driver). Reinstalling the new parts were straight forward, "no problem". (epg)

Parts Used:

Refrigerator Center Rail

Refrigerator Crisper Frame

EMILE from RACELAND, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken drawer slide

Extremely easy. Probably could have been done with eyes closed.

Parts Used:

Refrigerator Deli Drawer Glide

Irvin from Louisville, KY
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Freezer cold ; fridge warm . Freezer not defrosting.

Unplugged fridge
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done

Parts Used:

Refrigerator Electronic Control Board

Tim from Oxford, MA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Freezer not defrosting and making fridge run warm.

Super simple following the instruction video you posted. Thanks!

Parts Used:

Refrigerator Electronic Control Board

Brent from PRESCOTT, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Frost on the top edge of the freezer drawer

Put the gasket in the dryer for 15 minutes to warm it up. It fit much better after it was warm.

Parts Used:

Freezer Door Gasket - Black

Lee Ann from College Station, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

ICE BUILD UP AT BOTTOM OF FREEZER

DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.

Parts Used:

Grommet

Gerald from COLORADO SPGS, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

Parts Used:

Refrigerator Electronic Control Board

Marc from SEASIDE, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrig. was not holding proper temp in refrig compartment

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

Parts Used:

Refrigerator Electronic Control Board

Dan from Goldens Bridge, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.

The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one orientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.

Parts Used:

Refrigerator Electronic Control Board

Jim from HALTOM CITY, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

FREEZEING UP

in stalled new circuit board an thermostat an was fixed

Parts Used:

Refrigerator Electronic Control Board

Sherril from ROBBINSVILLE, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator was warm,freezer was cold

Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!

Parts Used: