ABB2224WES2 Amana Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
After 19 years of use, both side glides of deli tray had cracked.
Just 2 screws on each side - took them out, installed new glides with existing screws.
Very easy - ended up giving the fridge a thorough cleaning - fridge cleans so easy and quickly.
Very easy - ended up giving the fridge a thorough cleaning - fridge cleans so easy and quickly.
Parts Used:
-
Liz from ELMHURST, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket not sealing good
Opened the bottom freezer door and pulled the gasket out of the groove. Pulled it out around the door and put the new one back around the door and the pressed into the groove. There was one place that a flat spot didn't take shape so I used a blow dryer to heat it up some and now it seals perfectly.
Parts Used:
-
Vince from Miami, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clips on old toe kick plate were broken on one side. Would not stay on
Took the new kick plate out of the box. Snapped it into position. I have had a repairman for this refrigerator before. I would rather repair an appliance than buy a new one. I'm very proud that I thought to get a replacement part myself instead of calling my friendly repairman again. Saved a few dollars.
Parts Used:
-
Janet from SOUTH ST PAUL, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked humid drawer
-
Julie from BATH, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Draw Guide
Simple! Remove and replace two screws.
Parts Used:
-
Clayton from DUVALL, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drawer was cracked and fell apart
-
Charles from DURYEA, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken drawer glides
removed the shelf, unscrewed 2 screws in each side. Removed broken glides and installed new ones in the reverse order..
Parts Used:
-
John from JONESBOROUGH, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drawer glides were broke.
Couldn't have been easier. Took around 5 minutes. All you have to do is remove 4 Phillips head screws, put on new drawer glides, put the screws back in and your done.
Parts Used:
-
Greg from WAKEMAN, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The center rail was broken
The part just snapped in. super easy.
Parts Used:
-
Joella from THE DALLES, OR
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken right deli drawer guide
-
Herbert from MAHOPAC, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
FREEZEING UP
in stalled new circuit board an thermostat an was fixed
Parts Used:
-
Sherril from ROBBINSVILLE, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.
The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one orientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.
Parts Used:
-
Jim from HALTOM CITY, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken drawer slide
Extremely easy. Probably could have been done with eyes closed.
Parts Used:
-
Irvin from Louisville, KY
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer not defrosting and making fridge run warm.
Super simple following the instruction video you posted. Thanks!
Parts Used:
-
Brent from PRESCOTT, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Parts Used:
-
Marc from SEASIDE, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!