A59FN-5TVW-R Admiral Wall Oven - Instructions

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

very easy

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

Screwed in light bulb and glass protector

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

removed old and installed new

Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)