A182 Maytag Washer - Instructions

Found the 35 year old Water injector hose was dry, brittle, and cracked. Found the new part online at a reasonable price, but was unsure if the seal came with it or not. At $3 it was worth the gamble to buy the seal. Turns out that it did come with it so in another 35 years, I'll be ready ;-) Simple replacement of the hose, one hose clamp and fitting the lip of the new seal into the hole in the top of the tub. Access was gained quickly by removing the front panel (2 phillips screws) then removing 2 sheet metal screws in the front top corners and swinging the hinged top upwards. Piece of cake.

I turned the water off, detached the hoses and unscrewed the water inlet valve. I unhocked the wires and reattached the wires in the correct sequence on the water inlet valve. Done in 15 minutes.

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Easily

opened front of washer, removed motor, replaced glides and springs, installed motor and replaced belts. Installed new hoses and vacuum breaker. Its been a week now and no leaks or other problems.

I unscrewed the bottom two front phillip screws. Lifted the front panel at a right angle then popped off downward. Used a 3/8 socket to unscrew the two screws inside in the upfront corners holding the top to the sides. Pulled off the top bleach line.
Lifted the lid upward until it rested on the back wall. Unscrewed the water fill tube connected to the top side panel which to reach the inlet valve area. wrote down which color of the four wires went where. Unscrewed the back plate and disconnected the valve wires. Reversed procedure for installation. Cleaned other parts while I was in there. Installation went quick and smooth.

First I removed the 4 screws holding the old elbow in place. Then I removed the screw holding the cover over the upper access hole on the below the syphon break elbow. I reached up through the access hole and removed the old elbow from the inside. I slid the new elbow up through the hole, aligned it with the housing plate and then screwed the screws back in to hold it in place. I had to cut about 3" off my old drain hose, because the outside diameter of the old syphon break elbow was about 1/16" larger and had stretched the end of the hose too much to fit tightly on the new elbow. I then attached the drain hose to the new elbow and tightened the hose clamp and reinserted the hose into the drain and pushed the washer back into place. (I used the old hose clamp rather than the one included with the new elbow because it still worked fine and looked sturdier than the enclosed one.)

Our Maytag (A308) washer is now about 29 yrs old. I put in a PartSelect water valve 3 yrs ago. When it started leaking recently I found the cuplrit to be a flexible hose to the outer basis. The front came off easily (two screws at the bottom) and the hose clamps required some cleaning. I recommend purchasing new clamps. Under 30 minutes to get it running again.

My washing machine would only run hot water. Told my husband and we were ready to call the repair man when I suggested we try to order a part. So I Googled "washing machine repair". Clicked on the first sight I saw and 'searched 'no cold water' amd immediately saw explanation of our exact problem. The solution explained that MOST of the time the problem was the water inlet valve. So I ordered the part. My husband put the part on the machine and the process would have taken less than 10 minutes however the clamp was so rusted to broke and that required a trip to the hardware store. But I suppose clamp-life does not exceed 20 years. So mission accomplished and a great big thanks to all those who explained what they did to solve the problem!

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

First I unplugged the power cord from the wall. Then I turned off the water supply shut-offs at the wall and removed the hot & cold connections at the rear of the washer. Then I removed the two screws that held the assembly in the rear of the washer. I then pulled the assembly out about 3-inches, marked the new assembly to show the proper color of wire for each lug and disconnected the four wires at the lugs. I disconnected the rubber fill hose from the assembly and removed the assembly. Next, I installed the new assembly in the reverse order. It worked fine without any leaks & saved me from buying a new washer. My old washer now gets my clothes cleaner than it has for years - much quieter and quicker too.