All Installation Instructions for KitchenAid Mixer 9KSM95ER5

bent wisk

replace wisk order process very efficient and delivery prompt.

Parts Used:

Franciska from Carrollton, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Coating on beater wore off

Simply replaced the beater.Ordering part was simple and delivery was quick. I was back at baking in no time! Great service

Parts Used:

Mixer Flat Beater

Sandra from Jackson, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The Coating On My Flat Beater Had Chipped; Did Not Think It Was Safe Continue Using.

It was actually not a repair problem; just a replacement of a part. I ordered it one day and the next day the part was here. I have never had such a quick turn around in anything I have ordered. Thank you!!!!

Parts Used:

Mixer Flat Beater

Gennette from Yuba City, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

No repair I purchased a part.

The part fit great! PS. I may need to buy a gasket to go around my refrigerator door. I have an Amana Model #THI1853W, Serial No. 9502301998. Do you have instructions on how to install this gasket?

Parts Used:

Mixer Flat Beater

Ernet from Birmingham, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The screw cap no longer held the bowl in place.

This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!

Parts Used:

Mixer Screw Cap

Roberta from Glen Ellyn, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

head of screw was broken in half

I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie

Parts Used:

Mixer Thumb Screw

marjorie from juda, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Beater was peeling and chipped; thumb screw was worn & loose to the point it would fall out

It only involves reinserting the beater . And the thumb-screw was falling out so I cleaned the area and replaced the thumb screw. Very simple and easily done.

Parts Used:

Mixer Thumb Screw

Mixer Flat Beater

Carol from LIGNITE, ND
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

original part worn out, wouldn't hold mixing bowl

unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.

Parts Used:

Mixer Screw Cap

Diane from Holland, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Bent wires in a wire whip

I ordered a new wire whip and attached it just like it was the original. WALLA!!! Done.

Parts Used:

Wire Whip Mixer

Robert from Blairsville, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Screw cap or retainer wore out and wouldn't hold the bowl tight

Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly

Parts Used:

Mixer Screw Cap

Robert from Aitkin, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Sticky back disc on Orbital sander came apart (from old age )

remove 3 screws ,remove old sanding disc replace with new installl screws

Parts Used:

Worm Gear

David from Tolland, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Broken worm gear

Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.

Parts Used:

Worm Gear

Dallas from Atlanta, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

mixer would not turn on

removed one screw from back cover, loosened two screws holding speed control plate, removed one wire at a time from old unit to new, screwed two top screws back on mixer,plug mixer back in, adjust speed control screws until I reached correct speed, put back cover back on

Parts Used:

Mixer Speed Control Plate

John from Norfolk, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

worm gear had broken tooth and gear was loose on sprocket

I dismantled the machine to find the problem and to see what part I needed. Than when I ordered the part I saw the video of how to do it. If I had seen the video before I dismantled, I would have save a few steps. The video was very complete and accurate even it being an older model

Parts Used: