9512XUB Magic Chef Wall Oven - Instructions

Unscrewed old element from back of oven, disconnected and reinserted new element and screwed back into place. Voila! So glad to have saved the cost of a repairman. Where I live this would have been a $200 repair(part and service call) easily. This repair took no time at all. Very please as to how fast Parts service got the part to me. I use my oven a lot, so I was lost without it.

I took the broiler pan out of the shipping container and put it in the oven.

I made the mistake of thinking that, if the oven was off, there would be no voltage to the heating element. Wrong! I removed the element, wearing rubber gloves just for safety, and had no problem. But when I put the wiring back on the new element and tried to slide it into the hole at the back of the oven, one of the wires brushed the metal, sparks flew, and melted one of the wires. Even though the oven was off, this wire was hot. The solution was, of course, just to turn off the circuit breaker, reconnect the wire, and slide the element back in. It works fine now.

Turned off the breaker first. Remove the mounting screws and unplug the element. Then replace the new element. Then put in the mounting screws and turn the breaker on. Easy.

I TURNED THE POWER OFF !!! removed the two screws holding the element in place, disconnected the two power wires, installed the new element. Done, in less than five minutes.

Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.

Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.

remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.

All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.

This was too simple, turned off the power to the oven, undid the two screws, unplugged two wires, plugged wires into the new element, fastened the new screws and turned the power back on. Turned on the oven, what do you know, it works again!

The element did not come with instructions and none were needed.

Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem as to what to do. The unit is working great now.

Very easy. Didn't have to replace whole unit

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Went online and Googled for oven element by providing the serial and model number. Partselect popped up. I submitted the order and received and installed the new element within 5 days from start to finish. I recommend this website for replacement parts.

Found the model number, called the local parts store, they quoted $60 + $10 shipping because it was a warehouse order or something. So I came hear and got it for $42 + $7 shipping!

Turned off power, unscrewed the element, disconnected the clips from broken element, connected them to the new, screwed in the new element, and it was done

First, I want to say that this part arrived within 24 hours of placing the order. I was plesantly suprised. My husband did the repair and it was super easy. We had no problems.

Thanks PartSelect!