All Installation Instructions for Magic Chef Wall Oven 9512WUT

Heating element not working

Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.

Parts Used:

Range Bake Element

sherri from Topeka, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

would not heat

put the old one out,put new part in that easy,works like new

Parts Used:

Range Bake Element

robert from pantego, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

bake element burned through.

Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.

Parts Used:

Range Bake Element

Ronnie from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

the element broke was old

turned off power unscrewed plate that held in element unplugged socket from old element plugged in new one screwed plate back turned on power works fine

Parts Used:

Range Bake Element

Bryan from Thibodaux, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Coil burned out

1. Turned off oven electric power at circuit breaker.. 2. Removed 2 screws at coil at back of oven. 3. Pulled coil away from back of oven. 4.Pulled power wire clip up vertically from coil.One clip was too tight to pull up by hand. Used a pair of pliers. 5 Removed coil and put new coil in place with wireclips. and screws provided.

Parts Used:

Range Bake Element

Richard from Locust Grove, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Element was bad

Turned breaker off. Took out two screws holding it in place. Disconnected two wires. Put new element in. Works fine

Parts Used:

Range Bake Element

Irvin from Pride, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Element Replacement

Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.

Parts Used:

Range Bake Element

Marvin from Mill Valley, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Very Easy

Changed bake element in oven.

Parts Used:

Range Bake Element

Robert from North Canton, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Digital clock/timer broken

There were NO directions in the box, only a schematic. I was unable to locate the old one as my husband had removed it. So I had to guess which color wire connected to which plug. Good thing I guessed right the 1st time! so you might want to include installation instructions going forward.

Parts Used:

Clock-Timer

Jennie from kingwood, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Oven was not heating on bake setting

I unscrewed the old element from the back of the oven. Then I detached the wires and took the old heating element out. I then fit the wires into the new element and screwed it back in using the new screws. It was really easy! I was lucky to have my father in law show me how, since this was my first time to do it.

Parts Used:

Range Bake Element

Rebekah from Azle, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Door seal badly deteriorated

The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.

Parts Used: