9222XPB Magic Chef Wall Oven - Instructions

After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.

Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.

This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is held on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

unplugged the oven, unplugged the ignitor and removed the two screws

First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took about 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)

A very common problem for ovens not heating up is the oven igniter going bad. Depending on how much you use your oven, they only last about 5 years. It is easy to replace, but getting it off can be a little tricky since the screws are exposed to so much heat. Once you got it off, you can unclip the old one and clip the new one right in. Then bolt it back on, throw in the racks and shelves, and start cooking. I replaced the igniter twice, the temperature sensor once, and the control panel once.

very easy

Screwed in light bulb and glass protector