9222VPV Magic Chef Wall Oven - Instructions

TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.

took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like new .

removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine

First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3

1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I found the model, ordered the new seal, it arrived very quickly via mail and I replaced the seal. You simply slid off the old, slid on the new one and hooked it in place. No expensive repairman!

The trickiest part was making sure that the correct part was ordered. The first attempt was a failure. The seal was too long and the clips were too big.
After finding the correct part it was a breeze.

Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.

I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the old ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!

I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. After removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.

Great I can bake now

New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.