91F-4KX Magic Chef Wall Oven - Instructions

Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the igniter came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!

Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!

open oven door remove bottom tray pull off two screws unplug wire remove old part install new part

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

The Just Answer website answer felt certain that the igniter was the problem, and hence I ordered a new igniter.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.

We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a brand new oven!

I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.

Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.

Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!