91195987990 Kenmore Range - Instructions

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.

I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.

Fit like a glove.

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.

I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

The age of the system resulted in the cook top being heavily stuck by food-stuff to the range surface. The result was a twisting of the top when breaking it free. It caused the cooktop (a $500+ part) to crack diagonally across the whole surface. Thus ended the quick do-it-yourself process, and out to buy a new range. Parts-select was very good about the return process of the un-used and un-opened burner element.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions were clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.

Open oven door, unlock hinges and lift off. Lay on face on carpet or piece of cardboard. Remove 2 screws at top that go thru door and hold handle assembly. Remove 3 screws on bottom that hold bottom door trim to inner door. Carefully turn assembly over (hold it together so you don't drop the glass front!) and place back on floor, hinge side down. Lift off front glass and frame assembly. Lay flat on floor. Remove 4 screws that hold bottom door trim to side frames. If glass is stuck to bottom door trim (which it probably will be from rust and gunk)..... Remove 4 screws that hold side frames to upper handle assembly and completely lift glass and bottom trim out. Holding glass vertical, stand on the bottom trim piece and carfully work the glass up and out of the groove (do not wiggle it side to side or you will need to buy a new piece of glass). While you have everything apart, clean all the parts and remove the decade of gunk. Reassemble in reverse. The long screws at the top of the door that hold the upper handle assembly in place, have spacers around them, they thread onto the screws and maintain distance and alignment when re-assembling. Also, I found it easier to remove the handle from the upper piece (4 screws) to allow me to lay the whole assembly flat while screwing the bottom, side, and upper trim pieces together around the glass front. Once that is done, then put the handle back on before you assemble it to the inner oven door. That is it !

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!

After watching the demonstration on YOU TUBE by two separate persons, , I felt I could accomplish this repair job by myself. After all, if a 9 months pregnant lady on YOU TUBE can do it in 15 minutes then so could I. However, my particular stove turned out to be a bit more involved, and different than those whose demonstrations I had viewed! .. First turn off your electrical power at the circuit breaker. There is no need to unplug the stove, just test by turning it on and observing if the display is lit or the burners come on. If it doesn't then you are good to start the repair with the power off. 1) Open the oven door, then bend over and check underneath. There are two screws one on each side at the front. Using an 8 mm socket wrench undo those screws and put them in a safe place where they wont roll away. 2) I would suggest using an old towel or an old sheet once you have the stove top lifted to cover your work surface, so if you drop any little parts that might roll away, you will be able to just pick them up without a problem. Next you will need something to prop the stove top open or someone to hold it for you. I used the box that my new element came in and that worked well. 3) Here's where my stove differed.. I had a metal retaining bar across the two front elements holding them up in place. .. I unscrewed the two small screws that held it in place at the edge of the stove. (I just did it on the side where I was replacing the element). This does not release your element just the bar so you can get access to the element. 4) Next, using your pliers you will see a couple of round washers that have teeth, these are holding a spring in place on a metal peg, this keeps the element from falling or moving out of position.. It was a bit difficult releasing the washers but I eventually did it, with my pliers, and then had to straighten the washers out for use afterwards 5) Once the washers are off, this frees the spring and allows the element to be removed. from the bar. 6)Next, I recommend taking a picture of the wiring, so you will know what goes to where. There are four wires on the old element, so I just followed the color coded placement and fasten them in the same place onto the new element. The wires are a bit stiff to remove, and if you are using pliers be careful as they are fragile and could break. 6) When I removed my GE replacement element from the packaging, it turned out to be a little different, and did not have the two metal pegs on it. In order to make it fit so I could do the repair. I unscrewed the two pegs from the old element, then counting around the outside holes on the new element to get them in the exact same place, I then attempted to screw them in.. This was the difficult part as they did not easily fit, and I had to ream out the holes to get the posts to screw into the new element. 6) Once that was done, the rest is easy just putting it back together the same way you took it apart. With the pegs screwed in place and the four wiring clips put on the new element, then it should not take long to complete. Next fit the spring over the metal peg first, then put the peg through the hole on the retaining bar. Make sure you get them lined up in the correct position. If you don't then they will be out of alignment with the Ring marking on the glass surface. Check this before you get it all put back together. The retaining bar has four holes in it, so you will see what I mean. The metal pegs on my element went into two opposing holes. Once that is done, the spring goes over the peg, then the peg goes into the retaining bar, and lastly, the small round washer fits the bottom of the peg to keep the spring held tight and the element in place on the metal retaining bar. You are almost done. Next simply put the retaining bar back up, make sure your element lines up on the top of your stove in the position it was before, then put the two small screws