All Installation Instructions for Kenmore Range 91193608000

Old burner bowl needed to be replaced

Took out the old & put in the new one-Done!

Parts Used:

Burner Bowl - 8 Inch

bonnie from N KINGSTOWN, RI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Drip pans were filthy after years of overflow from pots during cooking

Luckily I retained the original manual and was able to order the drip pans through your company from the original manufacturer. Be sure range is turned off, lift the burner locking element, then lift the burner a bit. Remove the burner by pulling it, disconnecting it through the opening in the drip pan. Lift out the old drip pan and replace it with the new one. Then reconnect the burner through the opening in the drip pan. Press the burner locking element in place and the job is done

Parts Used:

Burner Bowl - 8 Inch

Drip Bowl - 6 Inch

Lee from Middle River, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Element blew hole in self then no power to burner.

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Melvin from Portland, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

temperature sensor went

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Parts Used:

Temperature Sensor Kit

Alex R from Randoff, NJ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

control switch had stopped working, burner wouldn't work properly

took out a couple of screws and replaced with new switch, plugged in switch wires. very easy

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Ruth from JACKSON, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

My burner trays were worn out and I needed new ones

I simply pulled the old ones out and replaced them with the new ones. It looks so much better and cleanes up well.

Parts Used:

Burner Bowl - 8 Inch

Burner Bowl - 6 Inch

Mary Jane from La Junta, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Could not adjust heat on burner.

Followed directions given by previous customers problems which we found on the internet.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Roy from Au Gres, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Cover was hit and damaged storage cover by electric wheelchair

removed 2 screws that hold the cover in place, inserted the new panel at the bottom, pushed top in place and reapplied the 2 screws.

Parts Used:

Front Drawer Panel - White

Jack from Hutchinson, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

electric burner shorted out and fried the switch

Removed two screws holding the housing in place and loosened two more on the back it order to free it. Switch was held i place with two screws, removed those. Transfered wires one by one on the new switch, which was identical OEM part, and replaced the screws. VERY simple.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

David from Greenwood, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven racks discolored ; due to being left in oven when the oven was cleaned.

Just removed the old racks..and replaced them with the new racks...That's all...

Parts Used:

Oven Rack

Marilyn from Jacksonville Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Broken Oven Rack

I'm so pleased with the ease of placing my order, the price, and the speed of delivery. My only challenge was figuring out the correct part to order, as I didn't have an owner's manual for the range when we moved into the house. But once I located the model # in the range's lower drawer, the website did a good job of guiding me toward the correct replacement part. In my case there was no "repair" involved; I was simply replacing a broken lower oven rack. I would definitely use this company again.

Parts Used:

Oven Rack

Claudia from Aurora, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

dropped & broke the oven light bulb cover

popped the new one on!

Parts Used:

Light Cover

joseph from san jose, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Original broil element had broken

Using a set of nut drivers, I unscrewed the element from the back of the stove, I unscrewed the thermometer, and unscrewed the brackets holding the element to the top of the oven compartment.

After the element was free, I pulled it out of the back of the oven, exposing the wiring. Using pliers, I disconnected the two wires, retrieved the new element, and re-connected the wires to the new element.

I reconnected the thermometer, pushed the element back into the oven, reattached it to the back of the oven and the brackets to the top of the oven compartment.

Parts Used: