All Installation Instructions for Kenmore Range 91193604010

Switch was not turning off range indicator light

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Charles from PORTLAND, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I had to replace surface elements and "burner bowls" or drip bowls

I pulled out the old parts, dropped the burner bowl into place, then plugged the prongs of the surface element into their sprocket. It took about ten seconds and used no tools.

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Surface Element - 8 Inch

Meg from PETERBOROUGH, NH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Grease spilled on old gasket----gasket hardened

Simply pulled old gasket from door and pushed new gasket clips into existing holes and tucked in ends at bottom of door.

Parts Used:

Door Gasket

Delores from Rocksprings, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Switch started arcing in the dial range of 2 to 8 in about a year.

Pulled the range out and unplugged it. Removed the back panel. Removed one wire at a time and plugging it in on the new switch. unscrewed the existing switch from the front panel (Two screws). Screwed the new one in, replaced the panel, plugged in the range and tested it. The new switch was a perfect OEM replacement and worked perfectly.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Brian from HONEA PATH, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old oven racks were ruined from self-cleaning oven

My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.

Parts Used:

Oven Rack

Joan from Holt, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The burner coil had shorted out and actually burnt a hole in my non stick pan and after I replaced that, it would not heat up again. I actually swapped the wires from the back burner, but the small coils use a different watt switch and it would barely boil water with the big coil. So I ordered this

First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

sherman from OPELOUSAS, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Incorrect oven temperature due to defective temperature sensor.

Performed repair using a video for reference.

Parts Used:

Temperature Sensor

Anthony from FARMINGVILLE, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The burner bowls were burnt through and nasty looking.

I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Isabel from The Colony, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Did not have a problem, just need an extra oven rack.

Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!

Parts Used:

Oven Rack

Catherine from Bethel, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replacement of old parts

Fortunately there was no repair needed, just a replacement of old parts, but I was very pleased with the speed of delivery and the quality of the parts. I'm a happy customer.

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Margaret from Norwalk, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner food on racks

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !

Parts Used:

Oven Rack

John from Metairie, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

In My Carelessness, I Ruined The Burners On My Stove Using A Really Abrasive Cleaner, And Had To Replace Them With New Ones. My Stove Looks Brand New, And I Feel Better!!

Nothing to it. Took off the old ones and put on the new! Tada - new stove!!

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Diane from Fraser, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

drwer slide under stove broke off.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

Parts Used:

REAR SUPPORT

paul from sewell, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broiler element was bad

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

Parts Used: