Models > 91193602000 > Instructions

91193602000 Kenmore Range - Instructions

All Instructions for the 91193602000
91 - 105 of 209
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner was not heating
unplug it and plug the new one in
Parts Used:
Surface Burner Terminal Block Kit
  • lucille from HAPPY CAMP, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
control switch had stopped working, burner wouldn't work properly
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Parts Used:
Surface Burner Switch - 8 Inch - 2500W
  • Ruth from JACKSON, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
temperature sensor went
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks
Parts Used:
Temperature Sensor Kit
  • Alex R from Randoff, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Previous owner left racks in during self clean
Took the old racks out andcslipped the new ones in
Parts Used:
Oven Rack
  • SHARON from EDMOND, OK
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced oven door gasket
Remove old stained gasket and replaced with new. Only $57.00!
Parts Used:
Range Oven Door Gasket
  • Paul from JACKSONVILLE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could not adjust heat on burner.
Followed directions given by previous customers problems which we found on the internet.
Parts Used:
Surface Burner Switch - 8 Inch - 2500W
  • Roy from Au Gres, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler coil burnt out
It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.
Parts Used:
Broil Element
  • Howard from LEXINGTON, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Parts Used:
Range Surface Element Control Switch - 6 Inch - 1560 W
  • Melvin from Portland, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic guide Broken
replaced Plastic Guides
Parts Used:
Bottom Drawer Guide
  • NICK from Vernon, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
9 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ONE OF SURFACE BURNER NOT WORKING
I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR
Parts Used:
Surface Burner Terminal Block Kit
  • QUANG from LANCASTER, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Parts Used:
Light Bulb - 40W
  • Roscoe G from ROCHESTER, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven door gasket needed replaced
Ordered the part, it arrived and 5 minutes later it a complete installation
Parts Used:
Range Oven Door Gasket
  • Mary from LONGS, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My burner trays were worn out and I needed new ones
I simply pulled the old ones out and replaced them with the new ones. It looks so much better and cleanes up well.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Mary Jane from La Junta, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hole in gasket
I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.
Parts Used:
Range Oven Door Gasket
  • Cynthia from Kidder, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
on off switch smoked and smelled hot
standard procedure, very simple
Parts Used:
Surface Burner Terminal Block Kit
  • john from MILROY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 91193602000
91 - 105 of 209