All Installation Instructions for Kenmore Range 9119358811

The small element blew out consequently shorting out the infinite switch.

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

Parts Used:

Range Infinite Heat Switch Kit

Susan from Bend, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Old Terminal Block was arcing.

Cut Wires to old terminal block and wired in new Terminal Block

Parts Used:

Surface Burner Terminal Block Kit

Robert from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven no longer heated except for Broil element

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven

Parts Used:

Bake Element

Derrick from Ypsilanti, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

support clips fell out

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

Parts Used:

Single Heating Element Support Clip

tomi from dallas, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

the drip bowls were worn out

simply replaced them.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

linda from STANTON, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Drip bowl from a big box store was too big even though both say 8”.

Ordered the part and set it in.

Parts Used:

Drip Bowl - 8 Inch

Kathleen from INCLINE VLG, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

element broke

took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.

Parts Used:

Bake Element

Richard from NEW BERLIN, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Drip pan was ruined by renter

I ordered a new drip pan. Piece of cake. Stove looks new again.

Parts Used:

Drip Bowl - 8 Inch

Karilyn from KEWADIN, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat

Removed old broken element and installed new one. Took less than 10 minutes

Parts Used:

Bake Element

Franz from CRESTVIEW, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

baking element arced and burned out

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

Parts Used:

Bake Element

Norman Levitz from Manchester Center, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

bake element was fried

I went by the video

Parts Used:

Bake Element

William from MARTIN, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Hinge broke on range. Oven door was very hard to open.

Followed the instructions from the video. The repair was really easy and quick.

Parts Used:

Hinge with Roller - Left Side

Ricky from LAWRENCEBURG, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Needed new drip bowl, was very hard to find one that fit my stove

Installed easily, was most impressed with the speed of delivery and it was the perfect size!!

Parts Used:

Drip Bowl - 8 Inch

Rosemary from BROOKFIELD, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used: