9117318810 Kenmore Range - Instructions

- removed the oven unit from the wall
- removed the aluminum backplate to expose the wiring
- Removed both glass wire nuts and disconnected the heating element\
- From the front, I removed both retainer screws and pulled the element wires through.
- In reverse order I reinsalled the new wires and screwed on the heating element.
-I reattached the electrical wiring and rear pane.
- I re-installed the unit into the wall.

I rempved the top and bottom doors, than the wire rackes followed by the bottom base of the oven. Then I removed the burner cover plate so I could get to the igniter.. I removed the cover plate for the wiring (2 wires), unpluged them, removed the igniter (2 screws). I had to cut the wires on the old igniter and couple the ends to the new igniter and then replaced everything by just reversing all that I did. Simple! Easy!

removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.

First shut down electric power to oven. remove
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

I followed the instructions of a PartSelect.com customer that was posted on the website. The instructions were great and the repair only took 15 mins. Before I found the PartSelect website I called the dealer who we bought the stove from and they wanted $ 250 for the repair. I went on the PartSelect Website and received the parts within 2 days.
Total cost $ 59.65 thru PartSelect. Thanks PartSelect--Great service and Great website

well first off I repair commercial HVAC equipment for a major drug company so I think I've done it all.I thought it cant be much different than any burner assembly.I made it harder than it had to be,anyone can do this.I removed lots of unneccessary things.Let me help you only take out the drawer on bottom of stove.so I started on top and worked my way down.save time and open the stove to were the door stops then have faith and give a good yank.this will remove the door,dont be afraid it will go right back on those two hinges easy.now that this is out of the way remove the bottom plate that covers the burner assembly (2 screws)in back pull it out then you see the igniter.as I said before with drawer pulled out remove the 2 1/4"nuts screws holding it up then from bottom.Unplug this stove then remove the 2 places its plugged in to.after you remove this there are 2 screws that hold it into the igniter remove them .cut the wires with enough room to re use the plug ends.strip the wires and use the wire nuts that they provide then put back together with new wires on new igniter then.re attach.put everything back together in the reverse order you took them apart.plug in stove and see the igniter light up again and light stove.do not call repairman you can do this.save your money for you its bad enough you have to buy anything else.

First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven.
PartSelect makes repairs quick & easy. It just takes a little smarts on your part.

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

Removed the door. Unscrewed the hinge from front of oven. Took broiler drawer out. Unhooked the spring. Removed hinge. Screwed new hinge in. Rehooked the spring. Slid oven door back on hinges. Mission accomplished. Oven door works like a champ. Wife happy.

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.

Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.