9117318611 Kenmore Range - Instructions

I followed the advice in the previous repair stories as this was very helpful.

I didn't know if polarity on the igniter mattered, so to be safe I marked the same wire on the old igniter and the corresponding wire on the new ignitor and plug, so it would be hooked up with the same polarity.

I took the burner element out to make it easier to replace the ignitor. I made sure to leave plenty of wire when cutting the connectors off the old igniter. Hooked everything up and it worked perfectly.

well,as with any repair that looks easy,i had to do a little more than what i had originally anticpated.
i was hoping for an access panel to the igniter,but after removing the lower drawer,there was only the heat shields and pans,about 20 screws later i got
to the igniter and spliced it in place,then reassembled it without too much fuss -now my 93 year old friend can bake her pecan pies for charity that is her favorite hobby-thanks

Got the igniter ordered. Since the original igniter was still on the appliance, I had to cut the wires on the original igniter in order to be able to attach the new igniter with the wire connectors supplied. Make sure not to cut the wire on the original(defective) igniter too short because otherwise you will have to splice again.

I went to the GE website, did the trouble shooting and read that 80% of the time the igniter was the problem. I read how others did the repair, ordered the part and followed their steps. My only problem was the two screws were at a tough angle to get to, if it wasn't for that it would've been 15 minutes

There are other descriptions here, but here's my story. I pulled the oven door off (pull straight up on it, it will come off) and removed the bottom warming drawer (there are plastic tabs on the outside of each side of the drawer--slide them and pull, several times on each side). I turned off the gas from behind the stove and unplugged the range, undid two screws at the back of the oven floor and lifted it forward and up. The burner is visible, but here is the hard part. The bolts holding the ignitor are underneath it and angled such that it is almost impossible to get any type of tool near them. I have small hands, and that helped. The screws are a bolt-head type or hex head, and I found that a one quarter inch open end wrench sort of fit. 6mm was too small and 7mm was too large. I managed to get the screws loosened after much struggling and manuvering, with half my body inside the oven, and once it was out, I was able to reach in from where the warming drawer was and unscrew the two wire leads attached from the ignitor to the power. They are held by plastic screwcaps. The reverse process was self explanatory, except that you should put the new ignitor in the oven and feed the wires down through the back panel, then attach the screwcaps to join the wires to the leads. Then go back in the oven and attach the ignitor, back screw first, and tighten it all the way, since you may not be able to reach it once the front screw is in. Also, use the screws that come with the new ignitor, since they are easier to start than the old ones. Tighten the screws as tight as you can get them so the ignitor doesn't wiggle, then turn the gas back on and plug it in, and test it before you put it back to gether. Mine worked, but it was a pain to do, kind of like working on an old car that wasn't designed to be fixed easily. Good luck.

Removed oven bottom panel. Removed lower drawer to access old igniter. Had to take a cover panel off to expose igniter. Unscrew two screws to remove igniter which was a bit awkward to reach. Then simply put new one in its place.

Per the instructions included with my part and from reading prior posts, I unplugged my range, removed my storage drawer, took the screws out of the bottom pan and removed. I found the igniter really easy to locate. As it was held in by a bracket that was soldered in, I found no need to remove many screws or to add the included mounting hardware as the part instructions suggested. I removed it, placed and mounted the new igniter (only two screws) before I snipped the connecting wires. Stripping the insulation material off of the wires seemed to be the MOST difficult part! I spliced the new to the old using ceramic caps enclosed with part, plugged in the range and fired it up...just to be sure it worked, and it did! I reversed the process to put it back together. Voila!

Using the crescent wrench, I first removed the bolt holding the cover plate that separates the wiring from the broiler section of the oven.

Then I removed the wire nuts that connected the wires from the igniter to the wires from the oven.

Then I removed the two screws that attached the igniter to the oven.

I then reversed the process, first attaching the igniter to the oven, then connecting the wires from the igniter to those from the oven using the wire nuts. Finally, I replaced the cover plate on the assembly.

The primary difficulty with the process was the small space to work in. One has to reach to the back of the broiler area to remove the bolt, screws and wire nuts. Some of these operations require two hands, and there's no room for both arms in this area.

However, that said, this is the third time we've replaced the igniter. It seems that it only lasts about 4 years before it needs to be replaced. It's not all that hard to do.

Just replaced the igniter, was pretty easy

Turn off electric supplying appliance,then remove oven bottom plate.Remove ignitor wires from controller and oven control,then remove two screws holding burner ,lift burner from gas valve,remove two screws holding ignitor.Replace with new,and re-assemble.

I removed the bottom cover inside the oven. Beneath that was another cover held by two screws. I removed these and the ignitor was right there. I removed the bracket screws and pulled the ignitor away from the back wall of the oven and cut the two wires close to the ignitor, leaving enough wire to reconnect the wires from the oven outlet to the new ignitor with the supplied wire nuts. Then I re-attached the bracket to the new ignitor and once that was done simply reattached the unit to the back wall of the oven. The whole job is pretty straight forward, the only difficult part being the limited work space INSIDE the oven.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)