91141489994 Kenmore Microwave Oven Combo - Instructions

Darthy from Dacula, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

Was this instruction helpful to you?

Powered Off completely

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

Parts Used:

Mohammad from Piscataway, NJ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

All power to the microwave went out.

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.

Parts Used:

Michael from East China Township, MI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Lower heat element burned out

Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.

Parts Used:

michael from marstons mills, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

I needed an oven with three racks, mine came with two.

just slipped it in

Parts Used:

BETTY from CYPRESS, TX
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven heating element was burnt through.

Identified part with Part Select, placed order. Opened the power breaker for the oven. Removed oven door (slides off) to improve access, removed burnt element (2 screw and 2 electrical blade terminals). Installed the new element and tested. Reattached oven door.

Parts Used:

george from Moorpark, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Wrench set

Was this instruction helpful to you?

Replaced damaged oven rack

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Parts Used:

Vicki from Irvine, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

no racks to oven

Easily glide in.

Parts Used:

Johnette from Baltimore, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Quit working

Just like the directions said. Very simple.

Parts Used:

William from Socorro, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Missing oven rack

I opened oven and pushed oven rack inside.

Parts Used:

Damaris from Easton, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Heating Element

Removed two screws, removed two wires, installed new element. So easy a caveman could do it.

Parts Used:

Bradley from Perryville, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Oven temperature was low when reading was correct

First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!

Parts Used:

Oven Sensor

Orion from Vancouver, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

microwave won't heat

bought a fuse but that didn't solve the problem. Guess I need a new microwave

Parts Used:

Stephanie from Kernersville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Parts Used: