91141066790 Kenmore Wall Oven - Instructions

Made triple sure electricity off. GE designed excellent access to box above oven. Remove three bolts above oven door on bottom of control panel. Slightly raise panel to take off control panel, let hang by wires. Fan in back wall behind panel and has two wires that unplug, four screws to remove. Plug in new fan, input 4 screws. Partselect excellent guide to make sure correct part was ordered, and very timely delivery. $85.00 part instead of $1500.00 new oven. Tip - Note that fan burns out when auto clean turned on. Stop doing that and problem doesn't repeat.

Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D

I gently pulled the door gasket up at hold pin points - which were spaced every 3-4 inches apart- the pins hold the gasket to the oven door. Once removed, I pushed the pins of the new gasket in holes of the door - starting at top center of door- until all pins were snapped in place. At the bottom of the door are two slotted holes through which each end of the door gasket terminates. Push ends of gasket into these holes until gasket lies flat to oven door.

I remove four screws two on the left side and two screws on the right side. I pull the oven out about ten inches, removed two screws that hold the hinge in place, took out the broken hinge and reverse the installation.

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

Turned off the breaker Pulled the wall oven out of the cabinet (4-screws) set it on the floor. removed the back cover , pulled wire clips removed old broken heat element. and reversed the process.

Replaced old with new.

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

Turn power to oven off at the breaker.
Remove access panel to upper control panel.
With the aid of an extension rod remove the hex headed screws succuring the fan to the baffle wall. Remove the fan. Replacement model did not have wire extending from it. So remove wire from original fan and attach it to the replacement fan terminals using an appropriate adapter. Install new fan in original position with original screws. Be sure to reconnect wire in the same orientation as the original fan (right side to white wire). Repeat process for the second fan in the upper control compartment. Handy trick for re-installing hex head screw in deep location....use a small piece of electrical tape to hold the hex head screw head inside the socket driver. After tightening is completed the tape will fall away from the screw.

Check that all wiring connections are back in place and tight. Re-install cover and turn the breaker back on. Test the oven out by heating it up again. It will take approximately 30 minutes to reach a steady state temperature inside the oven so that the circulation fans in the control panel turn on.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

First shut off circuit breaker. Removed two screws that hold the bake element in place pulled it out about two inches and dicconnected the two terminal wires. Replaced element in reverse order.
Ordered part and recieved the next day. WOW!!

I removed three screws to take the face plate off the oven to expose the electronic clock controller. I removed clock controller from the face plate and I then pulled one wire at a time off the old controller and plugged it into the new controller. A new latch assembly comes with the kit, the old latch assembly had three screws to remove it and the new one required only two to replace it. Again I pulled one wire at a time off the controller leading to the old latch assembly and plugged in the new latch assembly. I then replaced the face plate and I was finished. Start to finish approximately 30 minutes.

slid the old ones out and slid the new ones in. done

replaced lights in refrigirator and freezer

Alls well that ends well. General Electric changed the configuration of our Light bulb socket on our 1996 oven. It did not have a flange with two screws as the original. The new one, you will just connect it and twist it into place. It worked and we are very happy. Such wonderful people to deal with at this site. Our sincere thanks,
Richard and Shirley