91141066790 Kenmore Wall Oven - Instructions

Three things: 1) the instructions were faded and blurey. We ended up going to an internet blog to get more instructions 2) It was very difficult to get the connectors apart. You just had to tug with pliers. Had to be careful not to bend the wiring. 3) Needed to be warned to mark down well where all the conectors came from to get them back in the same place. You are unconnecting 10 different connectors.

thought I'd unplugged the oven, turns out I disconnected the stove top, which is gas and a separate unit. This cautionary tale is here to remind all to look at the clock of the appliance on which you are working to see if there is still power flowing to it.I failed to notice until I was working at disconnecting the old element to prepare the unit for my husband to repaire after returning home. Thought I'd clean things up a bit before he had to get in there. One bright, big and loud pow! and electric fearsomeness set in but caused little damage to me but my ego. I think I got a scorched knuckle-but not burned. Stuff like this is what keeps the repair techs in business. I set the screw driver down and noted the clock was still lit up. D'oh! Shut off the breaker to the oven, cleaned it up, and left the repair to my husband, who made short work of the replacement. Also, we were sorry not to have bothered to remove the door while working on the element connections at the back of the oven. It would have been easier on his back-especially considering we had difficulty grabbing the wires to plug into the new unit due to my precipitous approach. We used an old hemostat(the pincher like grabber things mentioned in a different post) acquired from his years in the ER, and the oven works fine, is clean(er) and I am all through eating my humble pie. Bake on!

Removed all mounting screws with ease. Had some trouble deciding how much pressure to use to get wire connections off old unit. Had to pull pretty good with needlenose pliers, a bit concerned at first that I might break connector. It took a good solid tug. Then since there were a high number of connections I made sure to do them only one at a time and make the conntection to the new unit rather than getting confused with more than one wire loose at a time. New part works great and saved a bundle on a repairman.

Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unplug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

Very was ti replace racks and knobs. Very fast mail service

1-SHUT OFF POWER. You can just unplug if possible, but it may be easier to flip the breaker to kill all power to the unit. 2-Use 1/4 in socket to loosen the two brass screws that hold the bake element into the back of the unit. 3-Gently pull out the wires, and pull the bake element from the wires. 4-Replace bake element and put back together. In all it took me longer to walk to the garage to get/replace my tools than it did to repair the unit. Don't be afraid to do it yourself...especailly cause it'll save you at least 50% on the job. :)

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

#1) Found electrical control breaker and moved to "off" position

#2) Removed two (2) screws with a nut driver, that were holding the bake element in position against the back wall of the oven. Gently pulled the original bake element out toward the door to expose the wire connectors from oven to element, then disengaged the connections.

#3) Removed the damaged element, replaced with the new element, reconnected the wires to the element, and returned same into the back wall opening and reinserted the two (2) screws with nut driver.

Repair was complete. Electrical breaker returned to on. Procedure Done!

Quick and easy, thanks!

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

remove the screws, replaced the element, replaced the screws.

Easy