9113658810 Kenmore Range - Instructions

The repair was easy and not very time consuming. It didn't take very long to fix the problem and thanks to this site, I was able to save the money I would have spent if a repair technician came out to do the same work. Now I can afford Christmas and cook too!

Removed bottom tray of oven, removed ignighter, unplug two wires.

I really can't add much more to the very good instructions already posted. You will need a flashlight to see the spring -- when connected it stands vertical with one end connected to the hinge. There are 3 holes you can connect to -- I used the middle one, #2. The other end of the spring is anchored to a hole/slot in the stove frame. It is very easy to position this spring. Be careful though, there's a lot of sharp sheet metal in there. You will need a phillips head screwdriver to remove/install 3 sheet metal screws that fasten the hinge to the stove.

Good friend said he could do it no problem at all!!!!!

We found the part right away from the diagram provided by your web site. We located the part number easily, paid on line and received in part in two days. My husband fixed it. It was relatively easy. Saved us money to pay someone to fix it. It could easily cost us more than $200.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

I open the oven, then pulled out the racks. I went on to remove the bottom pan by removing 2 screws from the back.. I then removed the broiler burner and disconnected the wires from the relay. I unscrewed the igniter and replaced it. I stripped the wires and connected the old connectors using the ceramic wire nuts. I put the burner back in place and connected the wiring.. I then trested the unit to make sure it worked . . .it did. I replaced the bottom pan and racks and once again made sure everything was working right.

Job done.

I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had frozen pizza 20 minutes later.

simple remove & replace. 2 min job. Couldn't be happier.

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

Pulled oven door up and off. Removed old hinge and installed new hinge. Replaced oven door. It was a very simple job. The whole project took less than 15 minutes.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.

Pulled the three screws off unhooked the spring then removed the hinge. attached the the new hinge to the spring put the screws back in slid door back on took less than 15 minutes.

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?