9113548813 Kenmore Range - Instructions

Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse order. Tested oven operation to ensure that the gas ignited promptly. (It did).

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...And then I installed
ignitor tightening the two screws and connected the two ignitor wires with the provided wire-nuts.
Mike Polcho

It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the burner tube back in place and secured it with the screw, replace oven bottom and door the whole repair took 20 minutes.

IThe schematics on the website were helpful for how everything goes together. I just followed the picture and then unscrewed all the screws that held the ignitor to the gas pipe. Have to pull out the gas pipe out first so you can get to the bolts, easy to do when you pull out the drawer and unscrew the hold down for the gas pipe.

No directions came with the part, and the length of the new wires weren't long enough nor did they have the attachment pieces that are needed to plug in the wires. However, helpful tips from others on the website told me that you have to cut the wires off the old part and screw the wires from the old to the new with the white plastic wire couplings. Worked like a charm!

It was a simple procedure, and I saved myself buying a new stove or paying someone else to fix it!

I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.

The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.

After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.

Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.

1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.

took off the door it should be very simple by opening the door just a little bit then pull up the door take out the shellves than take of the bottom of oven usualy there's 2 cap screws in back holding it down then take out the drawer from under the oven & unscrew the bracket that holds the flame pipe from underneath also unscrew the screw from inside the oven the holds the actual flame pipe in front next to the door then unscrew the old igniter from the pipe snip the old wire going out from the igniter & strip it a little & connect the new igniter put on the ceramic cover supplied together with the new igniter connect it back to flame pipe put everything back together you should be done. But make sure the wires are pushed down to underneath as much as you could also when you put back the gas pipe the wire should not be in the way underneath the oven