9113012990 Kenmore Range - Instructions

Removed the oven door and the bottom plate. Remove existing igniter by cutting the wire and unscrewing two small bolts. The installation of the new part is the reverse.

It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.

I changed out the old ignitor with the new one. New ignitor fit perfect on old mounting bracket. Attached the two wires and that was it.

I removed lower drawer, removed oven door,
took out rear screws to oven pan,removed screws that attatch ignighter to oven wall,disconnected wiring and removed old ignighter. reversed process to install new part. total repair time was about 20 minutes. Also take into consideration that i am a building contractor familiar to appliance repair etc.

I removed the igniter by first removing the oven racks then the oven pan and oven catch pans. I open the lower draw to the oven and removed the drawer. I reached back under the oven and clipped the wires that run to the igniter and striped a half inch of plastic to expose the wire. I removed the igniter from the burner and replaced with new igniter. I then fed the wires back through the hole the cut wires came out of and used the wire nuts supplied to connect. Replaced other parts in reverse order and tested. Works great.

The repair was easy and not very time consuming. It didn't take very long to fix the problem and thanks to this site, I was able to save the money I would have spent if a repair technician came out to do the same work. Now I can afford Christmas and cook too!

First had to disconnect the old igniter by removing screw with a small wratchet wrench. Then pull out approximately 3" of wire from the old igniter, cut off old igniter, attache replacement igniter with supplied wire nuts, shove excess wire back into wiring compartment and then attach the new igniter.

I had to replace the ignitor. The wiring was simple. Just had to connect two wires. The difficult part was removing and replacing the ignitor. It is suspended by 2 screws that are very difficult to access.

Troubleshooted ALL possible causes and after perusing the owners manual and PartSelect blogs. Can't say it enough, people!! Do your homework- there are 3 possible parts that can cause the oven not to light; Igniter, gas safety valve, or thermostat / power switch assy (oven control knob).
SAFETY FIRST...UNPLUG the stove before performing any of the following electrical circuit checks (besides voltage check, which is ONLY for those qualified for electrical circuit maintenance)

Remove oven door by opening slightly and pulling straight up- it will slide right off the hinges.
Remove the 2 thumb screws holding the lower oven plate and slide it toward the back while lifting up on rear of plate to clear the front flange and then remove the plate.
The burner tube baffle plate will come right off after removing the one retainer screw (1/4" nut driver).
(Optional)Remove the whole broiler drawer by sliding it fully open and lifting it up by the front end.
Now you'll have clear access to the igniter, which is mounted on the rearward end of the burner tube with two 1/4" machine screws. Disconnect the igniter wire connectors at the gas safety valve and wire harness. Remove it and SAVE the screws for mounting the new igniter!! NOTE: .
Handle the new igniter CAREFULLY!! (don't drop it or bang it against anything solid or the heating element will break).

1) Checked t-stat switch on oven knob - good (closed or 0 ohms when turned on). This verifies you are getting supply voltage to the igniter circuit. Lift the oven top by the front corners until the supports lock into place. Locate and disconnect wires on back of switch and measure ohms across switch terminals.
2) Checked voltage at igniter wire terminals with oven knob turned on (this step ONLY for those familiar with proper use of multimeter and training for electrical circuit maintenance). This verifies the gas safety valve switch is closed and correct voltage is available to power the igniter (120V).
3) Since I had proper power to the igniter wire terminals with the oven knob turned on past 200 deg., that verified a malfunctioning igniter.
4) I chose to solder and heat shrink the wire connectors to the new igniter but you can use the supplied ceramic wire nuts. Be sure to leave enough wire length when you cut the wires off the old igniter. Mount the new igniter to the bracket with the screws you saved and be sure to snug them good but DON'T overtighten and strip the threads!! Connect the two igniter wires to the gas safety valve terminal and the harness connector. Make sure the connections are snug!!
5) Reinstall the burner baffle plate and lower oven plate.
6) Remount oven door and turn on oven past 200 deg. The igniter element should glow bright red after a few seconds. Gas valve should open and burner will light a few seconds later.
NOTE: Make sure the gas cock for the oven (on the side of the main gas regulator valve) is flipped to the open position or gas will not flow to the oven burner. The main gas regulator valve is located under the range top toward the rear (trace the gas lines if you can't locate it readily)

Take bottom drawer out, take two 1\4 inch drive screws out from back bottom of inside of oven. Take out protector plate . Remove 1\4 inch drive screws from bottom burner[back of oven] where drawer was. Extract burner. Rest is self explanitory. Good luck. . . . . .

First I removed the bottom oven drawer then
I removed the heat shields. I removed the two
wires that connected the igniter and the two screws holding the igniter and removed it. I
replaced a wire connector on one side of the
igniter. The other igniter wire I soldered together
to the other wire. Then I replaced the igniter by
reconnecting the two mounting screws. Then I replaced the heat shields and the oven drawer.

Removed oven bottom panel. Removed lower drawer to access old igniter. Had to take a cover panel off to expose igniter. Unscrew two screws to remove igniter which was a bit awkward to reach. Then simply put new one in its place.

Removed the bottom cover plate and the bottom storage drawer. Disconnected the burner and removed it. Replaced the old igniter with the new one. The new one required the wire connectors from the old one to be spliced onto it. Reattached the ignitor to the burner and reinstalled the burner. Tested the new ignitor before reinstalling the cover plate and storage drawer.

I removed the bottom cover inside the oven. Beneath that was another cover held by two screws. I removed these and the ignitor was right there. I removed the bracket screws and pulled the ignitor away from the back wall of the oven and cut the two wires close to the ignitor, leaving enough wire to reconnect the wires from the oven outlet to the new ignitor with the supplied wire nuts. Then I re-attached the bracket to the new ignitor and once that was done simply reattached the unit to the back wall of the oven. The whole job is pretty straight forward, the only difficult part being the limited work space INSIDE the oven.

There are other descriptions here, but here's my story. I pulled the oven door off (pull straight up on it, it will come off) and removed the bottom warming drawer (there are plastic tabs on the outside of each side of the drawer--slide them and pull, several times on each side). I turned off the gas from behind the stove and unplugged the range, undid two screws at the back of the oven floor and lifted it forward and up. The burner is visible, but here is the hard part. The bolts holding the ignitor are underneath it and angled such that it is almost impossible to get any type of tool near them. I have small hands, and that helped. The screws are a bolt-head type or hex head, and I found that a one quarter inch open end wrench sort of fit. 6mm was too small and 7mm was too large. I managed to get the screws loosened after much struggling and manuvering, with half my body inside the oven, and once it was out, I was able to reach in from where the warming drawer was and unscrew the two wire leads attached from the ignitor to the power. They are held by plastic screwcaps. The reverse process was self explanatory, except that you should put the new ignitor in the oven and feed the wires down through the back panel, then attach the screwcaps to join the wires to the leads. Then go back in the oven and attach the ignitor, back screw first, and tighten it all the way, since you may not be able to reach it once the front screw is in. Also, use the screws that come with the new ignitor, since they are easier to start than the old ones. Tighten the screws as tight as you can get them so the ignitor doesn't wiggle, then turn the gas back on and plug it in, and test it before you put it back to gether. Mine worked, but it was a pain to do, kind of like working on an old car that wasn't designed to be fixed easily. Good luck.