90131 Litton Range - Instructions

Irina from Green Cove Springs, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Bowl -Drip and gasket

it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid

Parts Used:

Walid from Worcester, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Sockets for the burner elementss were burned out

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Parts Used:

Martin from Manchester, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

one of wire melted and broken off from receptacle

Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

Parts Used:

Young from Cordova, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Electrical receptacle for burner was defective.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

Parts Used:

gerald from Hillsboro, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

My heating element stopped working properly and one day just make a pop and stopped working altogether.

I followed the advice givin on the parts select website - it made it totally easy.

Parts Used:

Bake Element

David from San Francisco, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 6 people found this instruction helpful.

Was this instruction helpful to you?

missing one oven rack

put it on, perfect

Parts Used:

Oven Rack

Ana from Riverside, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Old burner stopped working right.

Was able to unplug the old burner and plug the new one in. Very easy.

Parts Used:

Surface Burner Element - 8 Inch

Paulette J. from Connell, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I wanted to purchase new drip pans, since those that I have are a bit grimy

I will begin by saying that not only will I continue to order my parts from PartsSelect, but I also highly recommend this business. If you call Whirlpool be careful that they forward your call for parts to some preferred vendor, which a customer might assume is Whirlpool but it is not. PartsSelect is the same type of business, but with outstanding customer service. With regard to the drip pan, Whirlpool had not updated the part number for these as I found out when i called them. Whirlpool no longer uses the drip pans without the holes which is a serious problem since this could be hazardous to the owners of these ranges if you are forced to purchase the drip pans with the holes in them. That said, I ended up keeping my old drip pans, because if you spill grease under the new ones with the holes in them and since the range design with the fan built in on the top does not allow you to lift the top to clean under the pans, you could end up with a grease fire. This is not the fault of PartsSelect and they handled my order in a manner that I would give them a rating of exceptional for customer service.

Parts Used:

Hedy from Richmond, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner coil was falling apart.

Used new plug in coil burner.

Parts Used:

Mary Kay from North Charleston, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

burned out coil

Simply slide out old coil by lifting cooktop pan; position new coil electirc elements in oven slots, slowly push in, then push coil tab into slot in pan for balance. No problems

Parts Used:

Surface Burner Element - 8 Inch

L from Richardson, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Two old Surface Burner Receptacles needed to be replaced.

I followed the instructions given on your great site. Thank you so much.

Parts Used:

Willis from Anaheim, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

surface burner stopped working. Was not heating up.

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

Parts Used:

timothy from south bend, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

My burner element had broken.

I ordere the new burner element. It arrived quickly compared to some of the things I order. I removed the broken burner element and plugged in the new one and that was all that was needed. It feels pretty good to have that burner working properly again.

Parts Used:

Surface Burner Element - 8 Inch

Mary from Hastings, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

old drip bowl was worn out

new drip bowl fit perfectly and was a snap to install.

Parts Used: