901040 Admiral Ice Maker - Instructions

Followed the other directions -- I have the bottom tray freezer. It was really easy to unscrew the screws -- a bit of a reach to get them all, but not a problem. Leave the top screws half-way in and it's a bit easier (the icemaker has the brackets that just sit on the screws). Thanks to everyone who left instructions!

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

First, I removed the ice bucket. Then I removed the two top left screws and bottom screw with a 1/4 inch nutdriver. I pulled the assembly out as far as the wiring harness would allow, disconnected the harness on the lower left side, and removed the unit. I removed the old motor cover and ice stop wire and placed them on the new unit. I then reversed the process. It went so fast that the freezer must have still been close to zero degrees because it filled with water within 15 minutes.

Barely a couple years old, was not getting any ice. I carefully selected the right part on this website and ordered. Around $150 and was easy install.

1. Mine was upper and lower freezer. you slide the freezer door out and lift it up, it will come right off.
2. pull out the tray above and ice bucket
3. Use a screwdriver to unscrew 2 screws above and one below the existing icemaker
4. unclip the power cable line

Thats it!

Point to note: the new piece you get will not have the power cable line, the water cover and the metal arm. I would think it should have for $150, but keep this as you will need a few little parts to complete the new part before installing it back.

VERY easy to do installation. Dont pay anyone to do this, it can be done easy!

Piece of cake. Removed two screws, pivoted old ice make up, lifted it out of the mounts. Installing the new one was just the reverse.

Identifying the correct replacement ice make was easy also, due to the photographs on PartsSelect.com

First I removed the screw holding the ice maker on the wall and then loosen two other screws in oreder to remove the maker. Once out, I replaced the maker with the new one. Then replaced it in the refrig.

First, unplug power to Fridge, then remove ice bin and set to one side, then remove the clip that holds the fill tube down by pulling up on it, and remove the fill tube. Remove the two top screws on ice maker assembly first, as the bottom screw will support unit. Then remove the single bottom screw. Rotate the Ice Maker slightly down and this will expose the electrical connector. With a short, small, flat head screwdriver in your left hand, depress the locking tab for the connector, while your right hand supports the assembly and pulls the connector outward to disconnect. Remove old Ice Maker, and remove the bin full lift wire, it's a slide in fit and install in your new unit. Check your fill tube water diverter on the right side of Ice Maker unit , you may need to remove the blank, it is U shaped and molded for easy removal, but use caution when removing to be on the safe side, this allows the fill tube to go down into the diverter, Re-Assemble in reverse order. Give the unit plenty of time to reach proper operating temp, and cycle. Make sure and discard your first Ice cycle.

I simply removed the 3 screws holding the unit into the freezer with a nutdriver, then disconnected the power plug (a little hard to get to, and requires releasing a small tab in a hole in the main body). The icemaker came right out with no problem. I then had to change out the water funnel inlet because mine had a different style than the one provided on the new one. This was easy also, just remove 2 phillips head screws that are set deep in 2 holes in the face of the motor drive unit, then pull the whole assembly apart far enough to allow the ejector blades to slip out of the hole through the inlet funnel, then snap the funnel loose to move it to the new one (the same technique to be used on the new one, then re-assemble in reverse order).

very easy, 3 screws,took old one out, take 2 inter screws out (of ice maker) of old unit to replace water feed cup on new unit very easy,installed had ice after 12 hrs.

I first loosened the hex screws and lifted the unit off. Then I unplugged old unit from the wiring harness. I did have to switch the inlet funnel since the new unit was a little different. I used the one from the old unit. I then plugged it back in, rehung and tightened the screws. The unit started operating within a few hours.

Ordered new part by the numbers and pics. and installation was so easy. I thank you very much

I simply removed 3 nut head screews and the old unit came off. I removed the ice level arm off the old unit and put on the new one. I removed the old wire harness and plugged into the new unit. I mounted the new unit, plugged it in and was done. I had ice in less than an hour. So simple my 11 year old could have done it without help.

used 1/4 inch wrench to remove bottom screw
and loosend tip screw and removed valve wires and water line

Most of the stories on repairing this ice maker indicated that was real easy until describing the Amana version. The fill tube attaches differently. The recommendation was to use your old "cup". I have found that to make the change required that you find a philips screw driver and locate two access holes in the motor end of the control unit. you can loosen those two screws (they won't fall out) all of the way and pull the control unit from the tray part of the ice maker. DON'T remove the three screws that hold the control unit together or rotate the sprocket. This will allow you to disassemble the parts that hold the "cup" in place. Just remember "if it isn't coming apart easily your not doing it right".

First I loosened 2 phillips head screws at the top of the ice maker (the one that is close to the front is a little difficult to get a screwdriver on). These 2 screws do not have to be removed. Took 1 screw out of the L-bracket at the bottom of the ice maker. I then slipped the icemaker upward from the 2 top screws and unplugged the electrical wires at the connector at back of the refrigerator to remove the ice maker. I then removed the front cover from it and placed it on the replacement ice maker. I also swapped the L-brackets on the two ice makers as the new one was bent. I then reinstalled the new Ice maker in the reverse order.