8TWGD6622HW2 Whirlpool Dryer - Instructions

Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..

Followed online video very easy and dryer works like new one....

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

pull the back off and replace the pulley.

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck