82199 LG Dryer - Instructions

Ordered a new one and installed it in a matter of seconds.
Not difficult!

I ordered the lint filter screen and when it arrived it looked exactly like the old one. It should have been nothing more than remove the old one and slide the new one in place.

Unfortunately, the new screen was about 1/2" wider than the old one and would not fit into the guide. After consulting by phone with your parts expert, we confirmed the model number and serial numbers, and eventually concluded that a design change must have been made by the manufacturer. We thought the only solution would be to also purchase the corresponding filter guide. So I ordered the guide. When it arrived, I installed it - a very difficult installation requiring putting my head and one shoulder into the dryer in order to get the screws out. (A long arm with two elbows would be nice.) After I got the old guide out, I discovered that it was exactly like the new one - 1/2" too narrow for the new filter screen. I reinstalled the old guide and returned both parts.

The dryer filter screen still has a hole in it and I am now waiting for my refund. I have no idea how to solve the problem.

The filter screen part number is 24053607, order number 18265310.

The guide part number is 24145665, order number 18348658.

Model number: DLE3170W

Serial number: 603KWMK6T539

Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement

With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.

Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.

Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.

There’s all sorts of videos on it I watched. It was actually very simple

An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.

Simple replacement

Watched a repair video. Very easy to replace, about an hour to repair.

Followed video provided on site

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

My cleaning lady brought her handy husband over Saturday to help me. The only tool we used was a Phillips-head screwdriver. I went online earlier in the week and found a good video put out by Repair Clinic and another one I found on You-tube on how to disassemble the dryer. After watching several times, I knew I could do it. We worked together, I cut my hand on the inside edge of the control panel, but, when I hit a snag, we watched that part of the video again and worked right through. Replaced the Thermistor, NTC first, not a problem. Then the Heater Assembly, not too difficult. I couldn't find where one of the remaining parts went, so, we reassembled the dryer and gave it a try. Worked like a charm. We did remove a lot of lint from inside the cabinet and around the felt liner on either end of the drum. It works like it did when it was brand new. Highly recommend to work with someone, so, you don't get frustrated. I am 65 years old and this was a no brainer for me, although I am somewhat mechanically inclined. Very empowering to accomplish this repair. Just follow the video.

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.