80529 LG Microwave - Instructions

Removed the retaining clip that keeps the door on, took the door off. Removed the plastic rim that is clipped into place. Removed old screws holding on handle and replaced.

Open the door and start at the outside perrimeter of the plastic moulding by inserting the putty knife and gently prying up.I started at the 2 latches that secure the door when it closes.Work your way around to the top and bottom. I was able to leave the portion of the plastic moulding by the door hinges still intact while removing the screws for the handle and replacing with the new one.After handle is on gently snap moulding back in place.Remember start at the inside of the door in the small opening at the outter edge of the door.

ordered on the part select web site, came quickly, order was correct

It was really simple. I used the putty knife the seperate the plastic trim, paying particular to start near the latches as someone else posted. Once the trim was pulled back Wow the screws were right there. I unscrewed the broken handle and attached the new handle. It was really easy and my wife thinks I'm amazing thanks for the help.

I replaced the whole component with all three switches in it even though only one switch was bad . Taking out one switch out of the holder unit would probably have damaged the unit that was holding the switches. Easy install and it works great again .

diagnosed defective 'door-shut switch' in the switch holder assembly. rather than replace switch, replaced entire locker holder assembly which made for a very simple and easy repair...not to mention very inexpensive.

Removed the inside door cover by taking a putty knife and inserting it by the door levers all around the door while pulling forward to seperate the cover so the screws that held the handle on could be reached. However, the part did not fit and had to be returned. Replaced cover by pinching it back in place.

With the amount of force needed to open the microwave door I can see this repair repeated. Some of the handle was still attached to the door so I could open it easy enough. there is a flamge covering the scerws to remove the handle. using a small flat blade screw driver aids in the removal of the flange to expose the screws. the square flange surrounds the entire frame of the door.remove the screws located in the recessed edge along the outside edge of the door.do this by viewing the location of the peices still attached to the door. after removing the screws and broken parts of the old handle,place the new handle in the cutouts where the handle is located,replace the screw,this may take some force since the handle is new. reposition the flange to the framevia the snaps along the edges and becareful not to force it because damage to the snaps are possible.thats it,two minute repair.

Used putty knife to unsnap tabs to separate inner trim on top, bottom and handle sides (left the hinge side attached), removed upper and lower screws, replaced handle, reinserted screws (tight fit, big fingers, several dropped screws, one under the stove = 15+ minutes), re-snapped trim

Not knowing which of the switches to replace I ordered all three in the assembly. Replacing the full assembly was easy, first unplug the microwave. Then remove the top cover to access the screws that hold the control panel in place and let the control panel hang. There are two screws that hold the assembly in place - remove those. I used needle nose pliers to pull the wires off of the switches and immediately put the wires on to the new assembly so there was no confusion on what wire went where. Place the assembly back in position, replace the two screws to hold it in, put control panel in place and secure screws. Replace top cover and plug in.

Separated the two elements on the front door. Then inserted the new handle and reconnected the front door. It was an easy installation.

Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.

Open the microwave door.
On the interior of the door, there is a plastic molding around the locks and most outer part of the door. Pop that with a flathead screwdriver or butter knife. You’ll immediately see two screw heads. Screw counterclockwise to release the fragments of the old handle. DO NOT THROW THOSE SCREWS AWAY. Reattach new handle using the same screws. Pop the piece of plastic molding back in and you’re done.

unscrewed the bottom of the microwave and unplugged old part then took the screw out and put new one in. Super easy!

I took the cover off and just put the new charcoal filter in