804655851A Frigidaire Dishwasher - Instructions

Ordered the rack and basket.for 122$ Basket never received . Did not get my money back for a basket. Was planing to return the rack, but easy return will cast me 82$. Keep in
Never buy anything from this company

Removed 6 torx headed screw (loosens the internal control panel) and 2 philips headed screws(allows for front door panel removal). 2 torx screws had to be removed from existing latch along with 2 plugs loosened, be aware of how the plugs were connected to the latch. Do the reverse; attach plugs to new latch and reattach latch with the 2 torx headed screws. The 6 torx screws reattach the control panel and the 2 philips screws reattach the front door panel (be sure the front door panel is properly aligned prior to installation of the philips screws).

First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!

After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.

I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.

Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

I read the instructions that others had posted and completed the repair in less than 5 minutes!

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Pulled off the old gasket and replaced it the same way with the new one.

Arm screwed on and immediately fixed the problem.

Open door, Lift out old ,replace with new.

I removed the access panel using a nut driver. One fastener on each side at the lower front panel. Move the two piece lower panel and set aside. Locate the broken spring. It will be on the floor under the dish washer. Remove the broken spring. Place the new spring end in the hole in the chord end and place the chord over the plastic guide. Use a pliers to stretch the spring and fasten it to the hole in the lower dishwasher frame at the back of the dishwasher. Check the door for proper tension. Replace the lower panel and secure with the two screws. I recommend replacing both springs at the same time to insure proper balance. If you only replace one spring you will be replacing the other in the near future.

I pulled the busted arm diddy off the doodad and popped the new part back on. Ta da.

Unplug dishwasher. Open the door. Remove two Phillips head screws holding the door panel on. Slide door panel down and out to remove. With door still open, remove the six T20 torque screws that hold the control panel. Behind the control is the latch assembly. Take a picture of the wires going into the latch assembly for installation reference(mine was black wires on left and white wires on right). Unplug the two sets of wires. Remove two T20 torque screws that hold the latch. Replace with new latch and reverse steps for installation.

Simply took the old one out, and put the new one in.