7WDF530PAYM3 Whirlpool Dishwasher - Instructions

just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.

This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Snapped right in. 30 seconds and done.

Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.

Snap in the missing track stop and twist snap the middle spray arm. That simple.

Screwed in new cap

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!

Put the kick plate under the dishwasher and screwed it in. Easy!

We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.

I opened the dishwasher door, removed the old tired seal in a manner of seconds. I measured the old seal against the new, same length, so no cutting. I started on one side pushing the seal in to the groove, made sure the seal was centered in the door. (not too long on one side or the other) It took less than 5 minutes to place the seal and check that it was all the way in, all around the door. I wiped the door down with some cleaner, where it contacts the seal. The door was harder to close, but I expected that until it breaks in. I ran a short load in the dishwasher with no leaks. :)