7KSM150PSZDR5 KitchenAid Mixer - Instructions

Unscrewed 3 Philips screws. Pried out the old screw cap. It had been there for 25 years and had flour, egg, etc. build up over the years. Did use a needle nose plier to lift it out. Put in the new one. Needed a rubber mallet to snug it down. Design has changed slightly over the years. Put the 3 screws back in and as they say in England, "you have an uncle named Bob."

watched instruction video (from Part Select), the demonstration was close enough to enable me to repair the mixer. Newer mixers are disassembled differently.

Per a video on this site, I removed the stand part, then removed the rear electrical cover and aluminum band which wraps around the mixer. Next, remove the drip ring and planetary gear (use a punch). Then remove the 4 screws securing the bottom housing and the 5 screws around the planetary gear housing. You should be able to pull the upper and bottom housings apart now. This exposes the control lever. Just unscrew it and replace it. Re-install all parts in reverse order.

Took the mixer down to the gear box. Found the plastic drive gear had a few stripped teeth. Did a search on the internet for the mixer gear. Found a couple of suppliers. Ordered the needed gear, pin and a bearing block just in case it was worn. The bearing block did not need to be replaced. Cleaned the broken off teeth from the gear grease and put the mixer back together. All worked fine when I plugged it in.

I found a video on how to repair mixer that would not turn. Watched video several times and replaced worn worm gear. Getting the old worm gear was the most difficult part of the job. I had to go purchase a pin punch ($5.50) with the correct tool is was easy.

Unscrew and dismounted the mixer, gather all pieces and screws, cleaned and washed every part, took away the old grease and replaced it with a new one, also looked carefully for the lost teeth and found them, Put grease in every part, put back and screwed all the pieces of the mixer, then tried the mixer which worked really well.

Great! Got the right part, the first time- did not break in shipping. Your web site made it very easy to pick out what I needed.

Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.

and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED

the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install

Replaced it with a new part. No installation or repair to maching was necessary

replaced

Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!

1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.

Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks