7KSM150PSZBW0 KitchenAid Mixer - Instructions

I watched a video on how to replace the worm gear. When I opened the mixer I noticed a small screw laying in the grease. I removed as much grease as I could and could not find anywhere that the screw would have come from. All the gears turned and looked fine so I replaced the grease put the mixer back together and it worked fine. I am thinking the small screw must have somehow fallen into the mixer when manufactured. So proud of my 70 year old self for getting the job done.

Watched a couple of youtube videos and it was easy.

Followed instructions found onllne at Kitchenaid.com and replaced seals with parts obtained from PartSelect.

Repair went well after I figured out how to dis-assemble the mixer. Used straight & phillips screwdrivers and a small hammer & punch to drive out 3 pins. Ordered part# PS734233 pinion & shaft as shown in the parts page, it arrived on schedule, received part # 240210-2. Only problem was the new pinion had 10 teeth, the old/failed pinion had 11 teeth. Could not learn from anyone I called at PartsSelect or Whirlpool if the 10 tooth pinion was the correct part to use.
The teeth appeared to mesh with the mating gear,
installed the new pinion, reassembled and it worked fine. Not sure if it made a noticable difference in the output shaft speed.

First i went to the Kitchen Aid web site and found a video on how to take a part the mixer. Followed the instructions from the video and it was very easy. The grease in the machine was black so i cleaned it out of the transmission and repack it with hi-heat wheel bearing grease that i got from a auto parts store it took about a 1/2 lb. then put the gasket in and back together and put the o-ring on. Have run for awhile and it is ok. Want to say that these are very well built machine.

Found control backplate out of adjustment. Should be nominal 3/8".Broken speed control spring which attaches to backplate bottom.
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed

Followed web site's videos. One step left out of video.

replaced gear, and brushes.

I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.

You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!

I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.

Unscrewed the existing screw cap, put the new one in place, replaced the screws. So easy!

Replaced gasket and O-ring. Problem solved. POC (Piece of Cake).

With a screw driver remove the screws holding the old base in place. With a flat head screw driver carefully pry and remove old mixer base. With 600 grit sandpaper clean and make smooth any burrs or rough spots in the mixer base recessed area. You can use some light grease and coat the outer edges of new mixer base and place in the now cleaned mixer base recessed area. The new base maybe a tight fit and not be fully seated in the recess. If a tight fit, place the piece of 2x4 piece of wood over the new part that is in the recess and carefully tap the base home using the sledge hammer. Check to see, if the base is fully seated. If not fully seated, tap again When fully seated replace the screws. You may have to adjust the height of the stand mixer head with mixer paddle attached for proper clearance between bowl and paddle. See your mixer manual for adjustment procedure

INSTALLED PHASE CONTROL BOARD AND SPEED CONTROL PLATE, BOTH AT SAME TIME
Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact