79641172212 Kenmore Washer - Instructions

Followed the video instructions provided.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.