All Installation Instructions for Kenmore Freezer 79577563600

water supply to ice maker leaked

Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new

Parts Used:

Plastic Tube - 5/16 Inch

john from locust valley, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

light out

slid screw driver under edge of switch, easy.

Parts Used:

Refrigerator Door Switch

Jack from Ellenton, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

light was not going on sometimes, or needed wiggling to work

purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !

Parts Used:

Refrigerator Push Button Switch

Nancy from Hallandale Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

plastic tube leaking at connector

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

Parts Used:

Holder,Bracket

GREG from STILLWATER, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Wrench (Adjustable)

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Frost in the freezer. Icemaker frozen.

I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.

Parts Used:

Clip

Teresa from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours

1 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Water/ice maker not working

Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.

Parts Used:

Micro Switch

Brent from ROGERS, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 34 people found this instruction helpful.

Was this instruction helpful to you?

Interior Light Would Not Turn Off

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

Parts Used:

SOCKET,LAMP

Thomas from Bay Shore, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Broken Drawer Slide Rails

Be sure to order two if both are broken. The picture shows two but only comes as a single item. Super easy to replace.

Parts Used:

Drawer Slide Rail

Brian from Fairmont, WV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Plastic door latch/ cam shaft broke on left side door

Removed white plastic trim and installed new latch / cam shaft

Parts Used:

Cam,Shaft

Refrigerator Camshaft

Reginald A. Green from Pelham, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Lamp cover and case had melted

I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!

Parts Used: