All Installation Instructions for Kenmore Refrigerator 79570339410

The switch became intermittent - Possibly a poor designe

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

Parts Used:

Refrigerator Door Switch

Sidney from ENDICOTT, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door light switch, 3rd one I have replaced in 6 years made in China.

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Parts Used:

Refrigerator Door Switch

Charles from CURWENSVILLE, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Replace switch

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

Parts Used:

Refrigerator Door Switch

Dean from HILLSDALE, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

door slight switch failed

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Parts Used:

Refrigerator Door Switch

Greg from CASA GRANDE, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

rail that holds meat tray broken

remove all trays from refrigerator , remove screw holding rail and install new rail.

Parts Used:

GUIDE ASSEMBLY,RAIL

Steve from GEORGE WEST, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Spring broken on front plate

Unscrew two Phillip screws on center hing , push frt plate down and replace.

Parts Used:

FRONT PLATE ASSEMBLY

RODNEY from GERMANTOWN, TN
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Replace the light switch for the refrigerator

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

Parts Used:

Refrigerator Door Switch

Karyn from DURHAM, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

the light did not work when door was opened. At first it would flicker then off completely.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Parts Used:

Refrigerator Door Switch

Alma from Winterport, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Side by side refrigerator. Right hand door (door stopper broken)

Phillips head screw driver required.

Door stopper attaches to door and front side of refrigerator. Located at the underside of the door at the front of the hinge.

Remove screw, keep screw for installation of new stopper. Remove damaged stopper, install new stopper using the original screw.

Parts Used:

STOPPER,DOOR

George from ROSEVILLE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ice Maker and Water dispenser stopped working

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/

Parts Used:

Water Inlet Valve Assembly

Donald from BETHPAGE, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker was broken

I just followed the instruction on the part , and everything was very easy.

Parts Used:

Refrigerator Ice Maker Kit Assembly

luis from DIAMOND BAR, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Lower ice maker water feed froze and caused leak. Needed new water valve.

Took pics of original install, removed old valve, water tubes & plugs. Installed new valve, reconnected electronic plugs, water tubes, turned water back on and all has been well since. Thank you for your timely delivery!

Parts Used:

Water Inlet Valve Assembly

Thomas from YORKTOWN, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Slow water for drinking

Just like on YouTube very easy to do

Parts Used:

Water Inlet Valve Assembly

Steven from SEBASTIAN, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice chute would not open.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Parts Used: