79096602500 Kenmore Range - Instructions

Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.

Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.

Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.

Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.

pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.

So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE

Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.

Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing