All Installation Instructions for Kenmore Range 79093022312

The element gets very even the control is at minimum

Removed the defective part. Install the new part, insert the connectors. Now its working

Parts Used:

Infinite Burner Switch - Large Element

adolfo from new york, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The Problem Was That The Plug Was Gone It Fell Down Out Of The Bracket

I took the old wires and plug off and replaced it with the new block it works fine

Parts Used:

Range Surface Burner Plug-In Block Kit

Elnora from Brundidge, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Three of four electric coils won't turn on

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

Parts Used:

Range Surface Burner Plug-In Block Kit

Arsenio from Beaverton, OR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

2 burner elements not heating

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

Parts Used:

Terminal Block Kit

Brian from MENASHA, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Sockets burnt out.

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

Parts Used:

Range Surface Burner Plug-In Block Kit

James from Bear, DE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Heating coils stop heating

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

Parts Used:

Terminal Block Kit

Sharon from TEMPLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Pulled the heating element on each burner installed the drip pans.

They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Sharon from AURORA, MO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

old drip bowls

replaced old drip bowls with new ones

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Vera from Snow Camp, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

sparking element

removed back and transferred four wires to new part and replaced back

Parts Used:

Infinite Burner Switch - Large Element

Phil from KERSEY, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Stove Burner wouldn't heat up

Someone did the repair for me.

Parts Used:

Range Surface Burner Plug-In Block Kit

Donna from Sandwich, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Arcing could be heard (and later seen) inside the switch

Switch was easy to replace. Some hex head screws to remove the panel and two screws to remove the switch. Though the plug in positions were totally different, all the quick connect terminals were marked on both switches.

Parts Used:

Infinite Burner Switch - Large Element

Joel from North Mankato, MN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Pitted, Eroded Drip Pans

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

Parts Used:

Drip Bowl - 8"