79070113705 Kenmore Range - Instructions

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

the wrong parts list came with the stove, so the part I ordered didn't fit. The people at partselect were great to work with.

Removed the old oven racks and put in the new ones.

Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.

Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

I just installed the extra rack and re-arranged the existing ones. Works great!

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, you can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.