79065319210 Kenmore Range - Instructions

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside top of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

The new part was shipped and recieved very fast.
I removed the old one and installed the new one going by how I took the old one out. It was simple to do even for a 75 year old lady.. Thanks.

Had to remove the old element and had problems with the element shorted on the quick disconnect. After having my son unplug the appliance and cutting the quick connect off. My son then installed a new quick disconnect and the bake element.

The problem I ran into Was; Having the right socket size for doing the project. After taking care of that problem it was fairly easily to disconnect the element and reconnect the new one. It's pretty self explanitory.

Took it off, ordered a new part and put it back on.
Ordered on Monday and got the part on Tuesday.

Loosen 2 screw with a 1/4 nut driver. Pulled element out to expose connections. Carefully disconnected old element and replaced with new element. Pushed wires back into holes and replaced the screws. (Note: Be careful not to let the disconnected wires slip back through the holes. This almost happen to me)

First I gave my roommate (an engineer) a screwdriver to remove the two screws that held the element in place. Then before I could hit the switch for the circuit breaker, he nearly fried himself by trying to take out the element! He gave up helping me after that.

Then I turned off the circuit, pulled the oven out and unplugged it, removed the racks from the oven, removed the two screws that hold in the element, and lifted up each side of the element and pulled each piece out. Unfortunately, they were a little stuck in back.

So I pulled out the oven, unscrewed the 6 or 8 screws that held up the back panel, and pulled the back panel off. I disconnected the two wires clipped to the element and pulled the old element out by lifting up and pulling them out. I then put in the new bake element, clipped the wires back on, put the oven's back panel on and screwed it in place, and then screwed the bake element back in with those two screws. Easy - a

For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!

Too dark to see, so left the power on so I cold use the oven light. Big mistake, shorted the fuse at the main box. No power in part of the house until finally figured out how to trip the fuse back on. Lesson learned. Never work on anything electrical without first turning off the power.

We called a local repair shop and they told us that it would take a month to get our part and it would cost over $50 for it. We went online and found PartSelect.com. The part was here in less than one week and it cost less than $40. My husband pulled the stove out from the wall took a screwdriver and unscrewed the screws, slipped in the new part and screwed the new screws in. It took him 15 minutes to fix it and now my stove works better than it has in many years!

I removed the screws holding the door together,removed the broken panel and replaced it with the new glass
The part fit correctly and the re-assembly was easy.

It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back together. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.

Removed the screws, replaced it with the new bake element, put the screws back in........and bam! I'm back in business. That's how easy this was to repair. Bake element cost me 40 bucks, appliance repair shop wanted about 200 bucks to repair.