All Installation Instructions for Kenmore Range 79061752104

new switch was not wired like old one

i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

Parts Used:

Infinite Burner Switch - Small Element - 240V

PERRY from LECANTO, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

20 of 32 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven drawer fell out

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

Parts Used:

Rear Drawer Glide

Donald from Gainesville, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

14 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner wont heat all of the time

removed old terminal block . cut wires and spliced new terminal block and insulated with shrink wrap. Very eazy

Parts Used:

Surface Element - 8 Inch - 2600W

Terminal Block Kit

Daivid from North Attleboro, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

14 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Door Handle had broken

Removed the broken door handle with a screwdriver, replaced the new door handle with a screwdriver. Took less than a couple of minutes to make the repair.

Parts Used:

Door Handle

Thomas from Plainfield, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

28 of 59 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the oven wouldn't work, but the range elements did

it was an easy repair, and i thought it was the clock /timer, but it was the probe.

Parts Used:

Electronic Clock Assembly

clinton from Columbia, MO
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver

13 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Racks needed to be replaced.

Slide out the old; slide in the new!

Parts Used:

Oven Rack

Peter from Chicago, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The stupid baking element died on CHRISTMAS EVE!

My husband removed the old one in a few minutes, the just popped the new one in when it came. Not for nothing, (where we purchased the stove) wanted $67 for the same part you all charged $49.00

Parts Used:

Bake Element - 240V

Minda from Madras, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

12 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner wouldnt heat

removed element , cut wires, conected wires,replaced element

Parts Used:

Terminal Block Kit

Doug from Ashton, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Draw Glide Broken Off Bottom Drawer.

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Parts Used:

Rear Drawer Glide

Kathleen from fall river, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No LED read out and no function!

I tested incoming and outgoing voltage at the timer! The timer showed to be defected!

Parts Used:

Electronic Clock Assembly

Rick from mount airy, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom elerment burnt into

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Parts Used:

Broil Element

Danny from Gaffney, SC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broil element was bad.

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Parts Used:

Broil Element