All Installation Instructions for Kenmore Range 79061750105

The burner on the top left (closest to front) would not turn off.

1 - Turn off the power from the panel. 2 - Unplugged the range from outlet. 3 - Unscrewed the black hex screws from the rear panel. 4 - Took a pic of the bad infinite burner switch to ensure the correct wires would connect to the new switch. 5 - Removed knob and unscrewed switch, then replaced with new switch. Matched all of the wires to like, L1, L2, P, H1 and H2. If any wires do not exist for your switch, it is ok because not all ranges use all wires.

Parts Used:

Infinite Burner Switch - Large Element

Sajeed from GRANADA HILLS, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Electric element would intermitantly go on high, even on low settings.

Slid stove out, disconnect power plug, removed top control panel with 4 screws. Unplugged two electrical connectors. removed knob and nut removing switch. Re-assembled in reverse order and test all functions.

Parts Used:

Infinite Burner Switch - Large Element

Sean from ASTORIA, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

8" burners were not responding correctly to the switches

Pull range away from the wall. Unplug range. Remove back plate covering the switches. Remove defective switch. Use bent paper clip to press center of terminal connectors and disconnect terminals. Reconnect each terminal of new switch as you go to avoid confusing terminals and connectors. Re-attach switch. Plug in range and test elements. Clean range area. Push range back into place, being sure to engage the anti-tip safety device.

Parts Used:

Infinite Burner Switch - Large Element

Carl from W SAND LAKE, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

shatered inside oven glass panel

I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.

Parts Used:

GLASS

Vito from RED BANK, NJ
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

wrong part

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Parts Used:

Main Terminal Block Kit

Barbara from WICKENBURG, AZ
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Broken inside glass

Followed your video and it was not hard at all

Parts Used:

GLASS

ERIC from INDIANAPOLIS, IN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Switch quit working and wouldn't turn

Take handle off, then back cover. Of course unplug power. Switch wasn't built exactly like the original but all you have to do is connect each wire to the same letter, number code as on the old one . Works like brand new!

Parts Used:

Infinite Burner Switch - Large Element

Jim from UNIONTOWN, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

replaced terminal block for element

followed the video provided on line which was very helpful..

Parts Used:

Terminal Block Kit

Donna from UNION, OR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The element gets very even the control is at minimum

Removed the defective part. Install the new part, insert the connectors. Now its working

Parts Used:

Infinite Burner Switch - Large Element

adolfo from new york, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

interior oven door glass cracked

All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.

Parts Used:

GLASS

lois from middletown, DE
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Heating coils stop heating

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

Parts Used:

Terminal Block Kit

Sharon from TEMPLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

sparking element

removed back and transferred four wires to new part and replaced back

Parts Used:

Infinite Burner Switch - Large Element

Phil from KERSEY, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

2 burner elements not heating

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

Parts Used:

Terminal Block Kit