79046803992 Kenmore Range - Instructions

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!

Removed the door from the range, disassembled the door, removed all broken glass fragments, installed the new glass, reassembled the door and reinstalled the door into the range. Straightforward and easy. Keep track of which screws go where and it is a breeze.

We turned off the power, took out the element, installed new element.

Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.

Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven

Followed instructions on website. Went perfectly.

Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.

I followed the instructions from the lady taking my order she talked me through the steps

Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same

The how-to video was helpful, though my old range has an extra spacer panel between the glass-top and oven, requiring an extra couple of screws to be removed, with different-sized Philips head.

1. Replacement part was not exactly like the original.
* Inner and outer elements lacked an insulating spacer.
* The two wiring terminals/docks were swapped.
* So had to attend to where the wires were going.
* Worked, just needed some observation & thought.

2. MOUNTING HOLES
a. Old element had clips mounted at holes 9 & 45.
b. Old element had the four-terminal wiring dock attached by screws at 71 & 72 (also where 0 would be), “ahead” of the small three-terminal port by about 5 number positions.
c. Corresponding holes in replacement were not the ones with pre-drilled insulating material. But it's really soft and easily drilled by hand. Probably could have just screwed directly into it.
d. Replacement four-terminal dock is “behind” the smaller one by a few number spots.

3. WIRING IS REVERSED
As noted, the two terminal docks are swapped, so watch the wiring.

Old terminal docks/ports were directly connected by a wire shunt that tied those terminals to the inner ring element.

The new element also has inner/outer burners, with no separation, but we can trace the wiring. Instead of a shunt, the docks are connected via the element. The right port on the small dock is connected to the inside burner, and that inside burner element exits into the large dock. That’s
the inside-burner circuit.

First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!

replaced it