79046802992 Kenmore Range - Instructions

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

repair was pretty simple. i pulled stove out from cabinet and unplugged it. Then i removed the screws that hold the face panel in place and gently slid out panel as far as i could without damaging wires. i had to remove the small switches that control the two two size burners as well as one thermostat on the right side so i can access the nuts holding the plastic end caps in place. i diagramed the color coded wires so i didnt mix them up.took off the old end caps replaced with new caps and put back together.. took about a half hour as this was my first time inside the guts of this stove.. stove is baack in place and as good as new again.

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

I previously replaced terminal blocks and elements so the infinite switch was the last stop before new purchase. I reviewed the online repair video. Unplugged the range and removed the three screws from the rear of the control panel. I Removed the knobs then removed two screws to release the front plate behind the knobs. I removed the two screws securing switch #1 and compaired to the new parts before removing wires. Wire locations were labled the same but in different sequence. I located the knob adapter for my knobs and set them asside. At first I thought the rod coming out of the new switch was too long and then figured out that the indentions allong the rod were to be broken off to the correct length. ( re-reading the included instructions was nearly useless - - not in plain language ) I used a pair of vice-grips clamped just below the length of rod I wanted to break off and it snapped off easily and cleanly for the most part. ( A word to the wise, this is some really soft metal at the breaks along the rod. I attempted a second break on one switch after mounting in the control panel and the thing broke off at the short end - - scary ) luckily I was still able to use it with my knobs and adapters. I relocated the switch wires to the new switch one at a time matching label to label ( L1, L2, H1, H2, P) then mounted the new switch into the control panel. I re-assembled the range and it is heating better than ever. Well worth the effort and minimal expense compared to a service call or replacement range.

Started with three screws on outer edge of door, which separated inner and outer door parts exposing the first set of screws on first piece of glass. There are four panes including inner and outer with two between. Keep track of the screws, be careful removing and replacing glass panes (i put mat down to rest glass on)and with nothing more than a screwdriver and windex to remove fingerprints etc from replaced glass, it was a breeze. Good luck! - FK, Bahamas

Took screws loose, unplugged old one plugged in new one put screws back

The repair went relatively easy. I even cleaned all the layers of parts when they were removed from the glass panel. I have to thank the excellent customer service and super fast delivery. Overall a quite easy task and $$ saving as well!

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.