79046262501 Kenmore Range - Instructions

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

Turn power to range off at electrical panel. Loosened control panel exposing switch. remove old switch and replace. reassemble.

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Easy as 1-2-3

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Trun off power, remove other knobs gain access to panel remove rubber connectors, which gave me access to switch. Study connections install new switch put panel back together,turn power back on run a series of test, all went well.

watched a U-Tube video on this subject.....worked like aa charm!!

Turn off the breaker! Remove the switch knobs. Using a Phillips screwdriver remove the two screws on the affected switch. With a large tip Phillips remove the three screws at the edge of each end of the panel and place it bottom side up on the stove top. Look at the bottom of the switch. Compare those numbers with the numbers on the new switch. Remove the wires one at a time and place them on the corresponding numbered terminal on the new switch. Be sure to put the mounting plate on the stem. Place the new switch in the cover plate and insert screws. Put cover over switches and insert the three screws on each side. Turn breaker on and turn burner switch on. Success!

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!

Turned of breaker to stove. Removed knobs. Removed four plastic nuts under knobs. Removed five screws that hold swith plate in place. Removed two screws that held actual switch in place. Swaped one wire at a time to new switches. (Switch was a newer model so seeing switch markings was critical to correct wire replacement!) Installed in reverse order. All in all. The job was easy and the new swith looks to be of a higher quality. This ia a gee-wiz--when the old switch failed it failed to the full on position. I had a pot of chicken slowly simering on Lo went to the garage to work a project came back in to a house filled w smoke/alarms going off and the burner on full high-glowing! The old switch was dangerous!

Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.

I did the repair in less then 5 minutes. I took out old element and put in new one and turned it on and I had heat. Works great Thanks the part came in 2 days what a wonderful suprise that was.