77JK-5EXWM Magic Chef Microwave Oven Combo - Instructions

Turned breaker off to oven, removed two screws disconnected two wires. Reversed order to install. Piece of cake. Stuart,in va.

Removed two screws. Gently pulled old element away from back of oven, exposing two wires. Disconnected the element from wires by pulling the ends apart with hands. Reconnected the wires with new element. LESS THAN FIVE MINUTES! Saved about a hundred bucks!. (Demo on You Tube.)

We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.

It was very simple. First thing I did was to go online to youtube and type in the kind of repair I intended to do. There were several short videos showing you how to do the replacement.It was easy and took about 30 to 45 minutes. First thing is shut off the power to the oven. ( Very important). You then need to take out two screws that hold the element in place. At this point, just pull the element toward the front of the oven. You will see some insulation at the hole where the wires come out. Slowly work the element forward until you see the fasteners on the wires ( two wires).Disconnect the fasteners and throw the old element out and put the new one in the oven.Connect the element, push everything back into the hole and screw the element to the back wall. You're done ! I had two wall ovens to fix.

The instructions reviewed in the Maytag Parts web site provided very good information that told me how to remove and replace the heating element. It took me about 15 minutes to complete the replacement. The oven then began to function properly.

I am impressed with the rate I was sent the replacement. I received the replacement within 24 hours after I submitted the request for the product.

Turned off the breaker first. Remove the mounting screws and unplug the element. Then replace the new element. Then put in the mounting screws and turn the breaker on. Easy.

I TURNED THE POWER OFF !!! removed the two screws holding the element in place, disconnected the two power wires, installed the new element. Done, in less than five minutes.

Unscrewed old element from back of oven, disconnected and reinserted new element and screwed back into place. Voila! So glad to have saved the cost of a repairman. Where I live this would have been a $200 repair(part and service call) easily. This repair took no time at all. Very please as to how fast Parts service got the part to me. I use my oven a lot, so I was lost without it.

I made the mistake of thinking that, if the oven was off, there would be no voltage to the heating element. Wrong! I removed the element, wearing rubber gloves just for safety, and had no problem. But when I put the wiring back on the new element and tried to slide it into the hole at the back of the oven, one of the wires brushed the metal, sparks flew, and melted one of the wires. Even though the oven was off, this wire was hot. The solution was, of course, just to turn off the circuit breaker, reconnect the wire, and slide the element back in. It works fine now.

I took the broiler pan out of the shipping container and put it in the oven.

Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.

Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.

The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !

I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.

Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.

Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem as to what to do. The unit is working great now.