7678894150 Kenmore Ice Maker - Instructions

After reading the stories on your site, I figured it had to be the motor control. Easy to take off, but had to take the tray off the freezer wall to get the ice out. Once I did that it was a piece of cake. Now I have ice (and vodka tonics...).

Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line

Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.

We replaced this part 5 years ago, so we considered ourselves "experienced" at this particular job. We followed the video at your site and after some sticky removal parts, we were able to put the new motor in and finish putting the freezer back in its original shape. After a few worried hours, we again had ice. The video was easy to follow and we couldn't be happier. Thank you for saving us hundreds of dollars.

Did not have to remove the complete ice maker. Only the front part that housed to motor assembly. Two Clips removes to cover and three screws removed the motor unit and the rest was in reverse. No wires to disconnect or connect. It just plugs in to unit. Works great and cheaper than from Sears Parts Direct shipping cheaper also. Will buy from Part Select again.
Thanks, Ron

First I disconnected the refrigerator. I snapped off the service door. taped closed the auto.door shut off located on the left side wall. the unit just pulled out,
disconnecting the power source, removed the plastic cover, unscrewed (3) screws and reattached the new unit . i reconnected the process in reverse.
if i had repairman do this it would have cost twice as much .

First I did the diagnostics and thought the water valve wasn't functioning so I replaced that, but it still didn't make ice. So I went on line and found the first thing to fix should have been the module and motor assembly. It was a real easy fix because I had pulled the ice maker before to investigate what was wrong. I just removed one screw and disconnected the electrical. There were four screws holding the motor assembly on. So I put the new motor on and had ice in 30 mnutes.

I don't know how he did the repair, but he told me it was simple, and I know it saved us a lot of money! Thank you for your excellent help and the delivery was like overnight!!
Submitted by
"The Wife"

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

removed the white plate, unscrewed 3 screws and replaced the part.

Watched the video...easy!

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

Watched a video on YouTube on how to replace the icemaker control assembly. The video showed unplugging power, turning off the water supply, and removing the entire ice maker from the freezer. After watching the video several times, I unplugged the refrigerator but did not turn off the water supply. I did not remover the entire ice maker from the freezer, but I did remove the wire shut-off arm. After that, I pried off front cover of the control assembly. The control assembly is held in place by 3 Phillips screws; I removed the screws, removed the icemaker control assembly, replaced the assembly with the new one, replace the cover and wire shut-off arm, and plugged the refrigerator back into the wall. Had ice in about an hour (seemed the system had a little delay before deciding to go to work!).

Easy, just removed the ice dispenser and the left support for the dispenser so I could get to the bottom screw easier. Three screws held the mold in place. The bottom screw had to be removed completely, but I just loosened the two top screws and lifted the mold out away from the wall and then disconnected the wiring. The end cover snapped of easy with a screw driver. I then removed the three screws holding the motor. then pulled the motor off.(the next square part under the cover. I did this before I realized that I could use a small screw driver and stick it into the holes to remove the mold and not mess with the outer screws. After I removed the mold, I replaced the new mold into position, without putting the white forky looking part back on so I had to take the two screws out and put the part in place before attaching the motor back to the mold. Everything went back together just like a charm. The ice maker is working good, easy job. Gone golfing now.

It took both me and my wife! One of the new parts we recieved was broke so we took the part off of the one that didn't work.

Unplug the fridge. Used the screw driver to remove the motor. Easy. Now putting the new one in was difficult because it has to line up exactly.
Thats what took 15 minutes but after me and my wife worked on it, we had a bucket of ice by morning!
We only knew how to do what we did because of reading these messages on this site. It came with no directions.

Removed icemaker by first removing the nutscrew that holds the cover to the electrical connection in place. Next, I removed the door then slid the icemaker out and diconnected the electrical connector. With the icemaker out, I R&R'ed the motor assy , reconnected the electrical, and slid the icemaker back in place. Next, I replaced the door, turned the icemaker switch on and waited. In about 30 minutes I heard the water being injected into the icemaker, and soon there was ice. The repair was easy and inexpensive. Tx to Partselect which I found on Google.