73065 LG Refrigerator - Instructions

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/

Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice

i changed the filter and was able to get water to the white coil at the bottom of the dispenser (left door) but could never get water to the icemalker.i also replaced the pump at the bottom of the door as well as the green ebr699172 dispenser electrical board.still can not get water to the icemaker.any help will be greatly appreciated.
paul

Took 2 screws out and disconnect wire and install new part.

Expensive to have repair man come out and find out that I’ve been mailed wrong spring again. My icemaker is on the left hand side this is the side of refrigerator- I need the spring for left side with the ice maker. Twice they have mailed me the Wrong spring that goes on the right hand side I have tried to explain this to the person that waits on me. Do I have to pay for another spring and mail this one back ?i have mailed one back and postage is getting expensive.

Removed trays and replaced broken sliding parts and replaced glass

Just popped it in, just as easy as that!

Opened box, unpacked shelf, placed in refrigerator. It took longer to open box than it did to install. Very easy!

Part arrived within expected time, removed from shipping box and installed.

Removed old part very easily and installed the new part without any problems. Used and adjustable wrench and screwdriver

I just followed the instruction on the part , and everything was very easy.

The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in
one piece and sits on the bottom of the Defrost Element.

The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.

First, remove power to the refrigerator.

To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.

Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.

As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.

Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.

Reinstall the ice maker mounting assembly in the reverse order it was removed.

Apply power to the refrigerator.

Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.





Pull the ice maker

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.