72183 - Instructions

Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.

removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!

Removed the damaged tube and replaced the it with a new one.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

very simple

The repair went well. They actually had to replace the motor. This saved me a lot of money having it repaired in this manner. Very professional & pleasant.

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.

I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.

Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.

I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.

really easy